- 您現在的位置：買賣IC網 > PDF目錄201871 > MC68HC11D3CFN2 (FREESCALE SEMICONDUCTOR INC) 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC44 PDF資料下載
參數資料
| 型號： | MC68HC11D3CFN2 |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 96/138頁 |
| 文件大?。?/td> | 1047K |
| 代理商： | MC68HC11D3CFN2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁當前第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁
Resets, Interrupts, and Low-Power Modes
MC68HC711D3 Data Sheet, Rev. 2.1
60
Freescale Semiconductor
4.4 Low-Power Operation
The M68HC11 Family of microcontroller units (MCU) has two programmable low power-consumption
modes: stop and wait. In the wait mode, the on-chip oscillator remains active. In the stop mode, the
oscillator is stopped. This subsection describes these two low power-consumption modes.
4.4.1 Stop Mode
The STOP instruction places the MCU in its lowest power-consumption mode, provided the S bit in the
CCR is cleared. In this mode, all clocks are stopped, thereby halting all internal processing.
To exit the stop mode, a low level must be applied to either the IRQ, XIRQ, or RESET pin. An external
interrupt used at IRQ is only effective if the I bit in the CCR is cleared. An external interrupt applied at the
XIRQ input is effective, regardless of the setting of the X bit of the CCR. However, the actual recovery
sequence differs, depending on the X bit setting. If the X bit is cleared, the MCU starts with the stacking
sequence leading to the normal service of the XIRQ request. If the X bit is set, the processing always
continues with the instruction immediately following the STOP instruction. A low input to the RESET pin
always results in an exit from the stop mode, and the start of MCU operations is determined by the reset
vector.
The CPU will not exit stop mode correctly when interrupted by IRQ or XIRQ if the instruction preceding
STOP is a column 4 or 5 accumulator inherent (opcodes $4X and $5X) instruction, such as NEGA, NEGB,
COMA, COMB, etc. These single-byte, two-cycle instructions must be followed by an NOP, then the
STOP command. If reset is used to exit stop mode, the CPU will respond properly.
A restart delay is required if the internal oscillator is being used. The delay allows the oscillator to stabilize
when exiting the stop mode. If a stable external oscillator is being used, the delay (DLY) bit in the OPTION
register can be cleared to bypass the delay. If the DLY bit is clear, the RESET pin would not normally be
used to exit the stop mode. The reset sequence sets the DLY bit, and the restart delay would be
reimposed.
4.4.2 Wait Mode
The wait (WAI) instruction places the MCU in a low power-consumption mode. The wait mode consumes
more power than the stop mode since the oscillator is kept running. Upon execution of the WAI instruction,
the machine state is stacked and program execution stops.
The wait state can be exited only by an unmasked interrupt or RESET. If the I bit of the CCR is set and
the COP is disabled, the timer system is turned off by WAI to further reduce power consumption. The
amount of power savings is application dependent. It also depends upon the circuitry connected to the
MCU pins, and upon subsystems such as the timer, serial peripheral interface (SPI), or serial
communications interface (SCI) that were or were not active when the wait mode was entered.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11D3CFN3 | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC08JB1DW | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PDSO20 |
| MC68HC08JB1P | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PDIP20 |
| MC68HC912BL16FU8 | 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 |
| MC68HC912BL16VFU8 | 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11D3CFN3 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11D3CFN4 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11D3CFU | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11D3CFU1 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11D3CFU3 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。