參數資料
型號： MC68HC11A8BCFN2
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： HCMOS Single-Chip Microcontroller
中文描述： 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC52
封裝： PLASTIC, LCC-52
文件頁數： 64/158頁
文件大?。?/td> 776K
代理商： MC68HC11A8BCFN2
MOTOROLA
6-6
SERIAL PERIPHERAL INTERFACE
MC68HC11A8
TECHNICAL DATA
6
WCOL — Write Collision
The write collision bit is set when an attempt is made to write to the serial peripheral
data register while data transfer is taking place. If CPHA is zero a transfer is said to
begin when SS goes low and the transfer ends when SS goes high after eight clock
cycles on SCK. When CPHA is one a transfer is said to begin the first time SCK be-
comes active while SS is low and the transfer ends when the SPIF flag gets set. Clear-
ing the WCOL bit is accomplished by reading the SPSR (with WCOL set) followed by
an access to SPDR.
Bit 5 — Not Implemented
This bit always reads zero.
MODF — Mode Fault
The mode fault flag indicates that there may have been a multi-master conflict for sys-
tem control and allows a proper exit from system operation to a reset or default system
state. The MODF bit is normally clear, and is set only when the master device has its
SS pin pulled low. Setting the MODF bit affects the internal serial peripheral interface
system in the following ways:
1. An SPI interrupt is generated if SPIE = 1.
2. The SPE bit is cleared. This disables the SPI.
3. The MSTR bit is cleared, thus forcing the device into the slave mode.
4. DDRD bits for the four SPI pins are forced to zeros.
Clearing the MODF bit is accomplished by reading the SPSR (with MODF set), fol-
lowed by a write to the SPCR. Control bits SPE and MSTR may be restored by user
software to their original state after the MODF bit has been cleared. It is also neces-
sary to restore DDRD after a mode fault.
Bits 3-0 — Not Implemented
These bits always read zero.
6.4.3 Serial Peripheral Data l/O Register (SPDR)
The serial peripheral data l/O register is used to transmit and receive data on the serial
bus. Only a write to this register will initiate transmission/reception of another byte, and
this will only occur in the master device. At the completion of transmitting a byte of da-
ta, the SPIF status bit is set in both the master and slave devices.
When the user reads the serial peripheral data l/O register, a buffer is actually being
read. The first SPIF must be cleared by the time a second transfer of data from the
shift register to the read buffer is initiated or an overrun condition will exist. In cases of
overrun the byte which causes the overrun is lost.
A write to the serial peripheral data l/O register is not buffered and places data directly
into the shift register for transmission.
相關PDF資料
PDF描述
MC68HC11A8BCFU2 HCMOS Single-Chip Microcontroller
MC68HC11A8BCP2 HCMOS Single-Chip Microcontroller
MC68HC11A8BMP2 HCMOS Single-Chip Microcontroller
MC68HC11A8BVP2 HCMOS Single-Chip Microcontroller
MC68HC11A1CFN2 HCMOS Single-Chip Microcontroller
相關代理商/技術參數
參數描述
MC68HC11A8BCFU2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
MC68HC11A8BCP2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
MC68HC11A8BMP2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
MC68HC11A8BVP2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
MC68HC11A8FN 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*