參數資料
型號： MC33394
廠商： 飛思卡爾半導體(中國)有限公司
元件分類： CAN
英文描述： Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(帶有多個線性穩壓器和高速CAN收發器的開關方式電源)
中文描述： 開關電源的多線性穩壓器和高速CAN收發器（帶有多個線性穩壓器和高速的CAN收發器的開關方式電源）
文件頁數： 29/44頁
文件大小： 641K
代理商： MC33394
29
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
After substitution, the calculated inductance value is L = 45
μ
H, which gives 47
μ
H standard component value.
The peak–to peak ripple current value is:
IL = 0.345 A.
The peak inductor current is given by:
ILpk = 0.5
IL + Io = 0.5x0.345 + 1.2 = 1.37[A]
The inductor saturation current is given by the upper value
of the 33394 internal switch current limit Ilim(max) = 3.0 A.
Considering also the inductor serial resistance, these
requirements are met, for example by the PO250.473T
inductor from Pulse Engineering, Inc.
5.2.1.2. Selecting the Catch Diode D1
The rectifier D1 current capability has to be greater than
calculated average current value.
The maximum reverse voltage stress placed upon this
rectifier D1 is given by maximum input voltage (maximum
transient battery voltage). These requirements are met, for
example by the HSM350 (3 A, 50 V) schottky diode from
Microsemi, Inc.
5.2.1.3. Selecting the Output Capacitor
The output capacitor Co should be a low ESR part,
therefore the 100
μ
F tantalum capacitor with 80 m
ESR was
chosen.
From the formula for calculating the ripple voltage:
VppESR =
IL x RESR = 0.345 x 0.08 = 28 [mV]
One device that meets both, the low ESR, and the
temperature stability requirements is, for example, the
TPSV107K020R0085 tantalum capacitor from AVX Corp.
Boost Converter Power Capability
The boost converter with selected components has to be
able to deliver the required power.
Due to the nature of this non–compensated PFM control
technique, the Boost converter output ripple voltage is higher
than if it utilized a typical PWM control method. Therefore the
switcher output voltage level is set higher than in the Buck
mode (in the Boost mode VPRE = +6 V), in order to maintain
a sufficient dropout voltage for the 5–volt linear regulators
(VDDH, VREFs) and to avoid unwanted Resets to the
microcontroller.
The most stringent conditions for the 33394 boost
converter occur with the lowest input voltage:
Vin(min) = 3.5 V
Io = 0.8 A
Vpre = +6 V
f = 200 kHz
Vfwd1 = Vfwd2 = 0.5 V
d = 0.75, duty cycle is fixed at 75% in boost mode
Figure 16. 33394 Switcher Topology – Boost Mode
IL
VRES
L
Vin
RLOAD
VO
+
–
+
CO
RD
Q2
ESR
D2
Vfwd2
IQ
IL
ILIM
I01
I02
IL1 < IL2
IO1 > IO2
T
t
IL1
IL2
L1 > L2
The input voltage drop associated with the resistance of
the internal switch Q1 and inductor series resistance can be
estimated as:
VD
Ipk(min)
RD
2.5 A
0.35
0.875 V
Where:
VD is the voltage dissipated on the major parasitic
resistances, RDSon of the internal power switch and inductor
series resistance RL.
For the worst case conditions:
RD = RDSon(max) + RL = 0.25 + 0.1 = 0.35[
]
Ipk(min) is the minimum internal power switch current limit
value.
Then the equation for calculating
IL can be modified as
follows:
[(Vo
Vfwd2)
(Vo
IL
Vin
VD
L
(Vin
VD)]
f
d
Vfwd2)
3.5
47
0.875
10
6
[(6
0.5)
(6
(3.5
0.5)
0.875)]
0.2
0.75
10
6
125[mA]
Then the maximum average input current can be
calculated as:
1
2
Finally, the boost converter power capability has to be
higher than the required output power or:
IinAve
Ipk(min)
IL
2.5
0.125
2
2.43[A]
Pin(max)
Pout
Where Pin(max) is the boost converter maximum input power:
h is the boost converter efficiency, in our case h is
estimated to be h = 85%, and includes switching losses of the
external power switch Q2 (MOSFET) inductor and capacitors
AC losses, and output rectifier D2 (schottky) switching
losses.
Pout is the boost converter output power, which includes
power loss of the output rectifier D2:
Pout
(Vo
Vfwd2)
Io
(6
0.5)
0.8
5.2[W]
Pin
(Vin
VD)
IinAve
(3.5
As can be seen, the boost converter input power capability
meets the required criteria.
0.875)
2.43
0.85
5.42[W]
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料
PDF描述
MC33395 Three-Phase Gate Driver IC(3相柵極驅動器)
MC33397 Dual/Hex Low-Side Switch with Both SPI and Parallel Input Control(帶SPI和并口輸入控制的2或6低端開關)
MC33399 “Local Interconnect Network” Physical Interface(“本地互聯網”（LIN）物理接口)
MC33486 Dual High Side Switch for H-Bridge Automotive Applications(適合于H橋自動應用的雙高端開關)
MC33661 LIN Enhanced Physical Interface(LIN網增強型物理接口)
相關代理商/技術參數
參數描述
MC33394DH 功能描述:IC POWER SUPPLY MULT-OUT 44-HSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
MC33395DWB 功能描述:馬達/運動/點火控制器和驅動器 TPD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33395DWBR2 功能描述:馬達/運動/點火控制器和驅動器 TPD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33395EW 功能描述:馬達/運動/點火控制器和驅動器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33395EWR2 功能描述:馬達/運動/點火控制器和驅動器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*