- 您現在的位置：買賣IC網 > PDF目錄359132 > MC33394 (飛思卡爾半導體(中國)有限公司) Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(帶有多個線性穩壓器和高速CAN收發器的開關方式電源) PDF資料下載
參數資料
| 型號： | MC33394 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | CAN |
| 英文描述： | Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(帶有多個線性穩壓器和高速CAN收發器的開關方式電源) |
| 中文描述： | 開關電源的多線性穩壓器和高速CAN收發器（帶有多個線性穩壓器和高速的CAN收發器的開關方式電源） |
| 文件頁數： | 23/44頁 |
| 文件大小： | 641K |
| 代理商： | MC33394 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
23
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
The Wake–up function can be disabled through SPI by setting
the WKUP bit to 0.
The CAN transceiver of the 33394 is designed for
communications speeds up to 1.0 Mbps. The use of a
common mode choke may be required in some applications.
When the 33394 CAN transceiver physical interface is not
used in the system design, the CAN bus driver pins CANH and
CANL should be shorted together.
4.16.3. CANH
CANH is an output driver stage that sources current on the
CANH output. It’s output follows CANL, but in the opposite
polarity. The output is short circuit protected. In the event that
battery or ground is lost to the module, the CANH transmitter’s
output stage is disabled.
4.16.4. CANL
CANL is an output driver stage that sinks current on the
CANL output. The sink type output is short circuit protected.
In the event that battery or ground is lost to the module, the
CANL transmitter’s output stage is disabled.
4.16.5. CANTXD
CANTXD input comes from the microcontroller and drives
that state of the CAN bus pins, CANH and CANL. A logic ‘0’
input drives the outputs to a differential (dominant) voltage,
where the CANH output is +3.5 V and the CANL output is +1.5
V. A logic ‘1’ input drives the outputs to their idle (recessive)
state, where the CANH and CANL outputs are +2.5 V. An
internal pull–up to VDDH shall guarantee a logic ”1” input level
if this input is left open. On power–up, or in the event of a
thermal shutdown, this input must be toggled high and then
low to clear the thermal fault latch. The faulted CAN bus
output(s) will remain disabled until the thermal fault latch is
cleared. The CAN bus data rate is determined by the data rate
of CANTXD.
4.16.6. CANRXD
This is a CMOS compatible output used to send data from
the CAN bus pins, CANH and CANL, to the microprocessor.
When the voltage differential between CANH and CANL is
under the differential input voltage threshold (recessive state),
CANRXD is logic ‘1’. When the voltage differential between
CANH and CANL is over the voltage threshold (dominant
state), CANRXD is logic ‘0’. In standby mode, input voltage
threshold remains the same. There is a minimum of 0.1 V of
hysteresis between the high and low (and vice versa)
transition points.
Figure 10. CAN Transceiver Block Diagram
–
–
25 k
25 k
5 k
5 k
2.5 V
10
μ
A
0.8 – 2.0 V
0.5 – 1.0 V
CANRXD
AWAKE
CAN_EN
VDDH
OverTemp
Sense &
Hysteresis
VDDH
CAN_EN
CANL
CANH
CANTXD
CANRXD
Complimentary
High/Low Side
Drivers w/
Current Limt
4.16.7. CAN Over Temperature Latch Off Feature
If the CANH or CANL output is shorted to ground or battery
for any duration of time, an over temperature shut down circuit
disables the output stage. The output stage remains latched
off until the CANTXD input is toggled from a logic ’1’ to a logic
’0’ to clear the over temperature shutdown latch. Thermal
shutdown does not impact the remaining functionality of the
IC.
4.16.8. CAN Loss of Assembly Ground
The definition of a loss of ground condition at the device
level is that all pins of the IC (excluding transmitter outputs) will
see very low impedance to VBAT. The loss of ground is shown
on the module level in
Figure 11. The nomenclature is suited
to a test environment. In the application, a loss of ground
condition results in all I/O pins floating to battery voltage. In
this condition, the CAN bus must not source enough current
to corrupt the bus.
4.16.9. CAN Loss of Assembly Battery
The loss of battery condition at the IC level is that the power
input pins of the IC see infinite impedance to the battery supply
voltage (depending upon the application) but there is some
undefined impedance looking from these pins to ground. In
this condition, the CAN bus must not sink enough current to
corrupt the bus. Refer to
Figure 12.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33395 | Three-Phase Gate Driver IC(3相柵極驅動器) |
| MC33397 | Dual/Hex Low-Side Switch with Both SPI and Parallel Input Control(帶SPI和并口輸入控制的2或6低端開關) |
| MC33399 | “Local Interconnect Network” Physical Interface(“本地互聯網”（LIN）物理接口) |
| MC33486 | Dual High Side Switch for H-Bridge Automotive Applications(適合于H橋自動應用的雙高端開關) |
| MC33661 | LIN Enhanced Physical Interface(LIN網增強型物理接口) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33394DH | 功能描述:IC POWER SUPPLY MULT-OUT 44-HSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| MC33395DWB | 功能描述:馬達/運動/點火控制器和驅動器 TPD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33395DWBR2 | 功能描述:馬達/運動/點火控制器和驅動器 TPD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33395EW | 功能描述:馬達/運動/點火控制器和驅動器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33395EWR2 | 功能描述:馬達/運動/點火控制器和驅動器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。