參數資料
型號： MC33394
廠商： 飛思卡爾半導體(中國)有限公司
元件分類： CAN
英文描述： Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(帶有多個線性穩壓器和高速CAN收發器的開關方式電源)
中文描述： 開關電源的多線性穩壓器和高速CAN收發器（帶有多個線性穩壓器和高速的CAN收發器的開關方式電源）
文件頁數： 21/44頁
文件大小： 641K
代理商： MC33394
21
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
4.15. SPI Interface to Microcontroller (Serial
Peripheral Interface)
The pins specified for this function are: DI (Data Input), DO
(Data Output), CS (Chip Select) and SCLK. Refer to Figure 3
for the 33394 SPI timing information. The delay, which is
needed from CS leading edge active to the first SCLK leading
edge transition (0 to 1) is approximately 125 ns. The SCLK
rate is a maximum of 5.0 MHz. The SPI function will provide
control of such 33394 features as VREFn regulator turn on/off,
VREFn fault reporting and CAN wake up feature activation.
Refer to Figure 7 & Figure 8 for the data and status bit
assignments for the 16 bit SPI data word exchange.
4.15.1. CS (Chip Select) Pin
The system MCU selects the 33394 to be communicated
with through the use of the CS pin. Whenever the pin is in a
logic high state, data can be transferred from the MCU to the
33394 and vice versa. Clocked—in data from the MCU is
transferred to the 33394 shift register and latched in on the
falling edge of the CS signal. On the rising edge of the CS
signal, output status information is transferred from the output
status register into the device’s shift register. Whenever the
CS pin goes to a logic high state, the DO pin output is enabled
allowing information to be transferred from the 33394 to the
MCU. To avoid any spurious data, it is essential that the
transition of the CS signal occur only when SCLK is in a logic
low state.
4.15.2. SCLK (System Clock) Pin
The shift clock pin (SCLK) clocks the internal shift registers
of the 33394. The serial input (DI) data is latched into the input
shift register on the rising edge of the SCLK. The serial output
pin (DO) shifts data information out of the shift register also on
the rising edge of the SCLK signal. It is essential that the SCLK
pin be in a logic low state whenever the chip select pin (CS)
makes any transition. For this reason, it is recommended
though not necessary, that the SCLK pin is commanded to a
low logic state as long as the device is not accessed (CS in
logic low state). When CS is in a logic low state, any signal at
the SCLK and DI pin is ignored and the DO is tri—stated (high
impedance).
4.15.3. DI (Data Input) Pin
The DI pin is used for serial data input. This information is
latched into the input register on the rising edge of SCLK. A
logic high state present on DI will program a specific function
(see Figure 7 for the data bits assignments for the 16 bit SPI
data word exchange.). The change will happen with the falling
edge of the CS signal. To program the specific function of the
33394 a 16 bit serial stream of data is required to be entered
into the DI pin starting with LSB. For each rising edge of the
SCLK while CS is logic high, a data bit instruction is loaded into
the shift register per the data bit DI state. The shift register is
full after 16 bits of information have been entered. To preserve
data integrity, care should be taken to not transition DI as
SCLK transitions from a low to high logic state.
4.15.4. DO (Data Output) Pin
The serial output (DO) pin is the output from the shift
register. The DO pin remains tri—state until the CS pin goes
to a logic high state. See Figure 8 for the status bits
assignments for the 16–bit SPI data word exchange. The CS
positive transition will make LSB status available on DO pin.
Each successive positive SCLK will make the next bit status
available.
The
DI/DO
shifting
first—in—first—out protocol with both input and output words
transferring the Least Significant Bit (LSB) first.
of
data
follows
a
33394 SPI Registers:
Serial Input Data/Control
Default Value
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
Name
Bit Definitions:
Bit 15 to 8 = 0
Default Value
1
1
1
1
1
1
1
1
Bit
7
6
5
4
3
2
1
0 (LSB)
Name
Bit Definitions:
Bit 7 — WKUP: WAKEUP activation. WKUP = 1: WAKEUP pin will signal CAN bus activity
Bit 6 — CAN_EN: Enables CAN receiver, will draw small current during power off
Bit 5 — VPP_V: Set VPP reference to 5V (1) or 3.3V (0), default is 5V
Bit 4 — EN_VPP: – Used to turn the VPP regulator off and on from the MCU
Bit 3 — VSEN: – Used to turn the VSEN regulator off and on from the MCU
Bit 2 — VREF3: – Used to turn the VREF3 regulator off and on from the MCU
Bit 1 — VREF2: – Used to turn the VREF2 regulator off and on from the MCU
Bit 0 — VREF1: – Used to turn the VREF1 regulator off and on from the MCU
WKUP
CAN_EN
VPP_V
EN_VPP
VSEN
VREF3
VREF2
VREF1
Figure 7. SPI Input Data/ Control Register
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料
PDF描述
MC33395 Three-Phase Gate Driver IC(3相柵極驅動器)
MC33397 Dual/Hex Low-Side Switch with Both SPI and Parallel Input Control(帶SPI和并口輸入控制的2或6低端開關)
MC33399 “Local Interconnect Network” Physical Interface(“本地互聯網”（LIN）物理接口)
MC33486 Dual High Side Switch for H-Bridge Automotive Applications(適合于H橋自動應用的雙高端開關)
MC33661 LIN Enhanced Physical Interface(LIN網增強型物理接口)
相關代理商/技術參數
參數描述
MC33394DH 功能描述:IC POWER SUPPLY MULT-OUT 44-HSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
MC33395DWB 功能描述:馬達/運動/點火控制器和驅動器 TPD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33395DWBR2 功能描述:馬達/運動/點火控制器和驅動器 TPD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33395EW 功能描述:馬達/運動/點火控制器和驅動器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33395EWR2 功能描述:馬達/運動/點火控制器和驅動器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*