- 您現在的位置：買賣IC網 > PDF目錄181329 > MBM29PL32BM10TN-E1 (SPANSION LLC) 2M X 16 FLASH 3V PROM, 100 ns, PDSO48 PDF資料下載
參數資料
| 型號： | MBM29PL32BM10TN-E1 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 100 ns, PDSO48 |
| 封裝： | PLASTIC, TSOP1-48 |
| 文件頁數： | 20/72頁 |
| 文件大?。?/td> | 450K |
| 代理商： | MBM29PL32BM10TN-E1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Retired Product
DS05-20907-4E_July 31, 2007
MBM29PL32TM/BM90/10
27
Temporary Sector Group Unprotection
This feature allows temporary unprotection of previously protected sector groups of the devices in order to
change data. The Sector Group Unprotection mode is activated by setting the RESET pin to high voltage (VID).
During this mode, formerly protected sector groups can be programmed or erased by selecting the sector group
addresses. Once the VID is taken away from the RESET pin, all the previously protected sector groups will be
protected again. Refer to “Temporary Sector Group Unprotection Timing Diagram” in
■SWITCHING WAVE-
FORMS and “Temporary Sector Group Unprotection Algorithm” in
■FLOW CHART.
Hardware Reset
The devices may be reset by driving the RESET pin to VIL from VIH. The RESET pin has a pulse requirement
and has to be kept low (VIL) for at least “tRP” in order to properly reset the internal state machine. Any operation
in the process of being executed will be terminated and the internal state machine will be reset to the read mode
“tREADY” after the RESET pin is driven low. Furthermore, once the RESET pin goes high, the devices require an
additional “tRH” before it will allow read access. When the RESET pin is low, the devices will be in the standby
mode for the duration of the pulse and all the data output pins will be tri-stated. If a hardware reset occurs during
a program or erase operation, the data at that particular location will be corrupted.
Write Protect (WP)
The Write Protection function provides a hardware method of protecting certain outermost 8K bytes / 4K words
sectors without using VID. This function is one of two provided by the WP/ACC pin.
If the system asserts VIL on the WP/ACC pin, the device disables program and erase functions in the outermost
8K bytes / 4K words sectors independently of whether this sector was protected or unprotected using the method
described in “Sector Group Protection" above.
If the system asserts VIH on the WP/ACC pin, the device reverts of whether the outermost 8K bytes / 4K words
sectors were last set to be protected to the unprotected status. Sector protection or unprotection for this sector
depends on whether this was last protected or unprotected using the method described in “Sector protection/
unprotection”.
Accelerated Program Operation
The device offers accelerated program operation which enables programming in high speed. If the system asserts
VACC to the WP/ACC pin, the device automatically enters the acceleration mode and the time required for program
operation will reduce to about 85%. This function is primarily intended to allow high speed programing, so caution
is needed as the sector group becomes temporarily unprotected.
The system would use a fast program command sequence when programming during acceleration mode. Set
command to fast mode and reset command from fast mode are not necessary. When the device enters the
acceleration mode, the device is automatically set to fast mode. Therefore, the present sequence could be used
for programming and detection of completion during acceleration mode.
Removing VACC from the WP/ACC pin returns the device to normal operation. Do not remove VACC from the WP/
ACC pin while programming. See “Accelerated Program Timing Diagram” in
■SWITCHING WAVEFORM.
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29PL32TM90TN-E1 | 2M X 16 FLASH 3V PROM, 90 ns, PDSO48 |
| MBN400GR12A | 400 A, 1200 V, N-CHANNEL IGBT |
| MBNC7-J-P-GN-ST-TH1 | BOARD TERMINATED, FEMALE, BNC CONNECTOR, SOLDER, JACK |
| MBNC7-J-P-HN-ST-TH1 | BOARD TERMINATED, FEMALE, BNC CONNECTOR, SOLDER, JACK |
| MBNC7-J-P-MN-ST-TH1 | BOARD TERMINATED, FEMALE, BNC CONNECTOR, SOLDER, JACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM30000 | 功能描述:BRACKET SIDE MOUNT RoHS:是 類別:工業控制，儀表 >> 配件 系列:* 標準包裝:1 系列:Aero-Motive® 130117 附件類型:拖車帶 適用于相關產品:標準盒式跟蹤系統 其它名稱:WM6183 |
| MBM30035001 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM30035015 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM300A6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES |
| MBM300GR12A | 制造商:n/a 功能描述:IGBT Module |
發布緊急采購，3分鐘左右您將得到回復。