- 您現在的位置：買賣IC網 > PDF目錄98010 > MB91F463NCPMC-GSE1 (FUJITSU LTD) 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MB91F463NCPMC-GSE1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP64 |
| 封裝： | 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, LEAD FREE, PLASTIC, LQFP-64 |
| 文件頁數： | 11/84頁 |
| 文件大?。?/td> | 1954K |
| 代理商： | MB91F463NCPMC-GSE1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
MB91460N Series
DS07-16607-4E
19
Precautions for the STOP mode
Set 1 to the bit 0 (OSCD1) of STCR register. When shifting to the STOP mode, a regulator switches to the stand-
by regulator (for low-consumption current).
Due to the limited drive current, stop the (programming/erasing) access to the A/D converter and Flash before
shifting to the STOP mode.
Serial communication
There is a possibility to receive wrong data due to the noise or other causes on the serial communication.
Therefore, design a board so as to avoid noise.
Consider receiving of wrong data when designing the system. For example, apply a checksum to detect an error.
If an error is detected, retransmit the data.
Notes on using external clock
When using the external clock, as a general rule you should simultaneously supply X0 and X1 pins. And also,
the clock signal to X0 should be supplied a clock signal with the reverse phase to X1 pins. However, in this case
the stop mode (oscillation stop mode) must not be used.
Notes on operating in PLL clock mode
If the oscillator is disconnected or the clock input stops when the PLL clock is selected, the microcontroller may
continue to operate at the free-running frequency of the self-oscillating circuit of the PLL. However, this self-
running operation cannot be guaranteed.
X0
X1
Note : Stop mode (oscillation stop mode) cannot be used.
Example of using external clock (normal)
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F464AAPMC-GSE2 | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91F464AA | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91F465CAPMC-GSE2 | 32-BIT, FLASH, RISC MICROCONTROLLER, PQFP144 |
| MB91F466BA | 32-BIT, FLASH, 96 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB91F464BA | 32-BIT, FLASH, 96 MHz, RISC MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F464ABPMCR-GSE2 | 制造商:FUJITSU 功能描述:MCU 32BIT FR 416K FLASH 100LQFP |
| MB91F464BB | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F464HB | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F464HBPMC-GSE2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F465BB | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。