- 您現在的位置：買賣IC網 > PDF目錄69020 > MB90F334APMC 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB90F334APMC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120 |
| 封裝： | 16 X 16 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LFQFP-120 |
| 文件頁數： | 28/120頁 |
| 文件大?。?/td> | 1210K |
| 代理商： | MB90F334APMC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
MB90330A Series
15
■ HANDLING DEVICES
1.
Preventing latch-up and turning on power supply
Latch
-up may occur on CMOS IC under the following conditions:
If a voltage higher than VCC or lower than VSS is applied to input and output pins.
A voltage higher than the rated voltage is applied between VCC pin and VSS pin.
If the AVCC power supply is turned on before the VCC voltage.
Ensure that you apply a voltage to the analog power supply at the same time as VCC or after you turn on the
digital power supply (when you perform power-off, turn off the analog power supply first or at the same time as
VCC and the digital power supply).
If latch-up occurs, the supply current increases rapidly, sometimes resulting in thermal breakdown of the device.
Use meticulous care not to let any voltage exceed the maximum rating.
2.
Treatment of unused pins
Leaving unused input pins unconnected can cause abnormal operation or latch
-up, leading to permanent
damage.
Unused input pins should always be pulled up or down through resistance of at least 2 k
. Any unused input/
output pins may be set to output mode and left open, or set to input mode and treated the same as unused input
pins. If there is unused output pin, make it to open.
3.
Treatment of power supply pins on models with A/D converters
Even when the A/D converters are not in use, be sure to make the necessary connections AVCC
= AVRH = VCC,
and AVSS
= VSS.
4.
About the attention when the external clock is used
Even when using an external clock signal, an oscillation stabilization delay is applied after a power-on reset or
when recovering from sub clock or stop mode. When suing an external clock, 25 MHz should be the upper
frequency limit.
The following figure shows a sample use of external clock signals.
5.
Treatment of power supply pins (VCC/VSS)
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating. Moreover, connect the
current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC pin and VSS pin
near this device.
X0
X1
OPEN
Using external clock
相關PDF資料 |
PDF描述 |
|---|---|
| MB90333APMC | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP120 |
| MB90F334APMC1 | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120 |
| MB90F395HAPMT | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120 |
| MB90F428GBPFV | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90F423GBPFV | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F334APMC1-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC1-G-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-SNE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-SPE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。