- 您現在的位置：買賣IC網 > PDF目錄377928 > MB90583CA (Fujitsu Limited) Octal Bus Transceivers With 3-State Outputs 20-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MB90583CA |
| 廠商： | Fujitsu Limited |
| 英文描述： | Octal Bus Transceivers With 3-State Outputs 20-CDIP -55 to 125 |
| 中文描述： | 16位微控制器專有 |
| 文件頁數： | 19/124頁 |
| 文件大小： | 2639K |
| 代理商： | MB90583CA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
MB90580C Series
19
I
HANDLING DEVICES
1.
Preventing Latchup
CMOS ICs may cause latchup in the following situations:
When a voltage higher than Vcc or lower than Vss is applied to input or output pins.
When a voltage exceeding the rating is applied between Vcc and Vss.
When AVcc power is supplied prior to the Vcc voltage.
If latchup occurs, the power supply current increases rapidly, sometimes resulting in thermal breakdown of the
device. Use meticulous care not to let it occur.
For the same reason, also be careful not to let the analog power-supply voltage exceed the digital power-supply
voltage.
Handling unused input pins
2.
Unused input pins left open may cause abnormal operation, or latch-up leading to permanent damage. Unused
input pins should be pulled up or pulled down through at least 2 k
resistance.
Unused input/output pins may be left open in output state, but if such pins are in input state they should be
handled in the same way as input pins.
Treatment of the TX and RX pins with the IEBus
TM
unused
3.
When the IEBus is not used, connect a pull-down resistor to the TX pin and a pull-down/pull-up resistor to the
RX pin.
Use of the external clock
4.
When the device uses an external clock, drive only the X0 pin while leaving the X1 pin open (See the illustration
below).
5.
Power Supply Pins (V
CC
/V
SS
)
In products with multiple V
CC
or V
SS
pins, the pins of a same potential are internally connected in the device to
avoid abnormal operations including latch-up. However, connect the pins external power and ground lines to
lower the electro-magnetic emission level to prevent abnormal operation of strobe signals caused by the rise in
the ground level, and to conform to the total current rating.
Make sure to connect V
CC
and V
SS
pins via lowest impedance to power lines.
X0
X1
MB90580C series
Open
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F583CA | 16-bit Proprietary Microcontroller |
| MB90583C | Octal Bus Transceivers With 3-State Outputs 20-LCCC -55 to 125 |
| MB90F591GPF | 16-bit Proprietary Microcontroller |
| MB90F598 | 9-Bit Bus-Interface Flip-Flops With 3-State Outputs 24-CDIP -55 to 125 |
| MB90V595 | 16-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90583CAPF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90583CAPFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90583CAPMC | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90583CPF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90583CPFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。