- 您現在的位置：買賣IC網 > PDF目錄98010 > MB90497GPMC 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MB90497GPMC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LFQFP-64 |
| 文件頁數： | 7/96頁 |
| 文件大?。?/td> | 2317K |
| 代理商： | MB90497GPMC |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
MB90495G Series
DS07-13713-6E
15
A/D Converter Power-up and Analog Input Initiation Sequence
Make sure to power up the A/D converter and analog input (pins AN0 to AN7) after turning on digital power
(VCC) .
Turn off digital power after turning off the A/D converter power supply and analog inputs. In this case, make
sure that the voltage of AVR does not exceed AVCC (it is permissible to turn off analog and digital power
simultaneously) .
Connecting Unused A/D Converter Pins
If you are not using the A/D converter, set unused pins to AVCC
= AVR = VCC, AVSS = VSS.
Notes for Powering Up
Ensure that the voltage step-up time (between 0.2 V and 2.7 V) at power-up is no less than 50
μs, in order to
prevent malfunction in the built-in step-down circuit.
Initialization
The device contains built-in registers which are only initialized by a power-on reset. Cycle the power supply to
initialize these registers.
Stabilizing the Power Supply
Make sure that the VCC power supply voltage is stable. Even at the rated operating VCC power supply voltage,
large, sudden changes in the voltage could cause malfunctions. As a standard for stable power supply, keep
VCC ripples (peak-to-peak value) at commercial power frequencies (50 Hz / 60 Hz) to no more than 10
% of the
power supply voltage, and momentary surges caused by switching the power supply and other events to more
than 0.1 V/ms.
If Output from Ports 0/1 Becomes Undefined
After power is turned on, if the RST pin is set to “H” during step-down circuit stabilization standby (during power-
on reset) , ports 0 and 1 output will be undefined. If the RST pin is set to “L”, ports 0 and 1 will go into a high
impedance state. Take careful note of the timing of events outlined in figures 1 and 2.
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F497GPF | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64 |
| MB90F498GPMC | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64 |
| MB90802SPF-G | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP100 |
| MB90803PF | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP100 |
| MB90822PFV | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90520A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90520B | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90522 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90522A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90522APFF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。