參數資料
型號: M68HC711D0CFB
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, 2 MHz, MICROCONTROLLER, PQFP44
封裝: QFP-44
文件頁數: 43/124頁
文件大?。?/td> 5398K
代理商: M68HC711D0CFB
CENTRAL PROCESSING UNIT
TECHNICAL DATA
3-5
tions. Shift and rotate instructions operate with and through the carry bit to facilitate
multiple-word shift operations.
3.1.6.2 Overflow (V)
The overflow bit is set if an operation causes an arithmetic overflow. Otherwise, the V
bit is cleared.
3.1.6.3 Zero (Z)
The Z bit is set if the result of an arithmetic, logic, or data manipulation operation is
zero. Otherwise, the Z bit is cleared. Compare instructions do an internal implied sub-
traction and the condition codes, including Z, reflect the results of that subtraction. A
few operations (INX, DEX, INY, and DEY) affect the Z bit and no other condition flags.
For these operations, only = and - conditions can be determined.
3.1.6.4 Negative (N)
The N bit is set if the result of an arithmetic, logic, or data manipulation operation is
negative (MSB = 1). Otherwise, the N bit is cleared. A result is said to be negative if its
most significant bit (MSB) is a one. A quick way to test whether the contents of a mem-
ory location has the MSB set is to load it into an accumulator and then check the status
of the N bit.
3.1.6.5 Interrupt Mask (I)
The interrupt request (IRQ) mask (I bit) is a global mask that disables all maskable in-
terrupt sources. While the I bit is set, interrupts can become pending, but the operation
of the CPU continues uninterrupted until the I bit is cleared. After any reset, the I bit is
set by default and can only be cleared by a software instruction. When an interrupt is
recognized, the I bit is set after the registers are stacked, but before the interrupt vector
is fetched. After the interrupt has been serviced, a return from interrupt instruction is
normally executed, restoring the registers to the values that were present before the
interrupt occurred. Normally, the I bit is zero after a return from interrupt is executed.
Although the I bit can be cleared within an interrupt service routine, “nesting” interrupts
in this way should only be done when there is a clear understanding of latency and of
the arbitration mechanism. Refer to SECTION 5 RESETS AND INTERRUPTS.
3.1.6.6 Half Carry (H)
The H bit is set when a carry occurs between bits 3 and 4 of the arithmetic logic unit
during an ADD, ABA, or ADC instruction. Otherwise, the H bit is cleared. Half carry is
used during BCD operations.
3.1.6.7 X Interrupt Mask (X)
The XIRQ mask (X) bit disables interrupts from the pin. After any reset, X is set by de-
fault and must be cleared by a software instruction. When an interrupt is recognized,
the X and I bits are set after the registers are stacked, but before the interrupt vector
is fetched. After the interrupt has been serviced, an RTI instruction is normally execut-
ed, causing the registers to be restored to the values that were present before the in-
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
M68HC711D3CFB1 8-BIT, MROM, 1 MHz, MICROCONTROLLER, PQFP44
M68HC711D3CP1 8-BIT, MROM, 1 MHz, MICROCONTROLLER, PDIP40
MAC7101CPV50 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP144
MAC7141CFU50 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP100
MAC7111CPV50 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP144
相關代理商/技術參數
參數描述
M68HC908LB8 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers
M68HC916Y1CFC 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-Bit Modular Microcontroller
M68ICS05B 功能描述:SIM PROGRAM FOR 68HC705B16 RoHS:否 類別:編程器,開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像,彩色(RGB) 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
M68ICS05C 功能描述:SIM PROGRAM FOR 68HC705C8A/C9A RoHS:否 類別:編程器,開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像,彩色(RGB) 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
M68ICS05JP 功能描述:SIM PROGRAM FOR 68HC705JP7/JJ7 RoHS:否 類別:編程器,開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像,彩色(RGB) 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP