- 您現在的位置：買賣IC網 > PDF目錄98007 > M41T256YMH7TR (STMICROELECTRONICS) 0 TIMER(S), REAL TIME CLOCK, PDSO44 PDF資料下載
參數資料
| 型號： | M41T256YMH7TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO44 |
| 封裝： | 0.330 INCH, PLASTIC, SOH-44 |
| 文件頁數： | 9/30頁 |
| 文件大小： | 271K |
| 代理商： | M41T256YMH7TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
M41T256Y
Clock operation
Clock operation
Year, Month, and Date are contained in the last three registers of the TIMEKEEPER
Register Map (see Table 3 on page 18). Bits D0 through D2 of the next register contain the
Day (day of week). Finally, there are the registers containing the Seconds, Minutes, and
Hours, respectively. The first clock register is the Control Register (this is described in the
Clock Calibration section).
The nine Clock Registers may be read one byte at a time, or in a sequential block. The
Control Register (Address location 7FF8h) may be accessed independently. Provision has
been made to assure that a clock update does not occur while any of the nine clock
addresses are being read. If a clock address is being read, an update of the clock registers
will be halted. This will prevent a transition of data during the read.
Reading the clock
The nine byte clock register (see Table 3 on page 18) is used to both set the clock and to
read the date and time from the clock, in a binary coded decimal format. The system-to-user
transfer of clock data will be halted whenever the address being read is a clock address
(7FF9h to 7FFFh). The update will resume either due to a Stop Condition or when the
pointer increments to a RAM address.
This prevents reading data in transition. The TIMEKEEPER cells in the Register Map are
only data registers and not actual clock counters, so updating the registers can be halted
without disturbing the clock itself.
Setting the clock
Bit D7 of the Control Register (7FF8h) is the Write Clock Bit. Setting the Write Clock Bit to a
'1' will allow the user to write the desired Day, Date, and Time data in 24-hour BCD format.
Resetting the Write Clock Bit to a '0' then transfers the values of all time registers (7FF8h-
7FFFh) to the actual clock counters and resets the internal divider (or clock) chain.
Note:
The Tenths/Hundredths of Seconds Register will automatically be reset to zero when the
WRITE Clock Bit is set.
Other register bits such as FT, TEB, and ST may be written without setting the WC Bit. In
such cases, the clock data will be undisturbed and will retain their previous values.
Stopping and starting the oscillator
The oscillator may be stopped at any time. If the device is going to spend a significant
amount of time on the shelf, the oscillator can be turned off to minimize current drain on the
battery. The Stop Bit (ST) is the most significant bit of the Seconds Register. Setting it to '1'
stops the oscillator. Setting it to '0' restarts the oscillator in approximately one second.
相關PDF資料 |
PDF描述 |
|---|---|
| M41T256YMT7F | REAL TIME CLOCK, PDSO44 |
| M41T56MH6F | REAL TIME CLOCK, PDSO28 |
| M41T60Q6F | 1 TIMER(S), REAL TIME CLOCK, QCC16 |
| M44C510-P40 | 4-BIT, MROM, MICROCONTROLLER, PDIP40 |
| M44C510D-XXX-DOW | 4-BIT, MROM, MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M41T256YMT | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit 32K x8 SERIAL RTC |
| M41T256YMT7 | 功能描述:實時時鐘 Serial 256K (32Kx8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T256YMT7E | 功能描述:實時時鐘 Serial 256K (32Kx8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T256YMT7F | 功能描述:實時時鐘 Serial 256K (32Kx8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T256YMT7TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit 32K x8 SERIAL RTC |
發布緊急采購，3分鐘左右您將得到回復。