參數資料
型號： M41T256YMH7TR
廠商： STMICROELECTRONICS
元件分類： 時鐘/數據恢復及定時提取
英文描述： 0 TIMER(S), REAL TIME CLOCK, PDSO44
封裝： 0.330 INCH, PLASTIC, SOH-44
文件頁數： 11/30頁
文件大?。?/td> 271K
代理商： M41T256YMH7TR
M41T256Y
Clock operation
Tamper indication circuit
The M41T256Y provides an independent input pin, the Tamper Pin (TP) which can be used
to monitor a signal which can result in the setting of the Tamper Bit (TB) if the Tamper
Enable Bit (TEB) is set to a '1.'
The Tamper Pin is triggered by being connected to VCC/VBAT through an external switch.
This switch is normally open in the application, allowing the pin to be “floating” (internally
latched to VSS when TEB is set). When this switch is closed (connecting the pin to
VCC/VBAT), the Tamper Bit will be immediately set. This allows the user to determine if the
device has been physically moved or tampered with. The Tamper Bit is a “read only” bit and
is reset only by taking the Tamper Pin to ground and resetting the Tamper Enable Bit to '0.'
This function operates both under normal power, and in battery back-up. If the switch closes
during a power-down condition, the bit will still be set correctly.
Note:
Upon initial battery attach or initial power application without the battery, the state of TEB
(and TB) will be undetermined. Therefore TEB must be initialized to a '0.'
Tamper event time-stamp
If a tamper occurs, not only will the Tamper Bit be set, but the event will also automatically
be time-stamped. This is accomplished by freezing the normal update of the clock registers
(7FF7h through 7FFFh) immediately following a tamper event. Thus, when tampering
occurs, the user may first read the time registers to determine exactly when the tamper
event occurred, then re-enable the clock update to the current time (and reset the Tamper
Bit, TB) by resetting the Tamper Enable Bit (TEB).
The time update will then resume, and after either a Stop Condition or incrementing the
address pointer to a RAM address and back, the clock can be read to determine the current
time.
Note:
The Tamper Bit (TB) must always be set to '0' in order to read the current time.
Calibrating the clock
The M41T256Y is driven by a quartz controlled oscillator with a nominal frequency of
32,768Hz. The devices are tested not exceed ±35 ppm (parts per million) oscillator
frequency error at 25oC, which equates to about ±1.53 minutes per month. When the
Calibration circuit is properly employed, accuracy improves to better than +1/–2 ppm at
25°C.
The oscillation rate of crystals changes with temperature (see Figure 11 on page 20).
Therefore, the M41T256Y design employs periodic counter correction. The calibration
circuit adds or subtracts counts from the oscillator divider circuit at the divide by 256 stage,
as shown in Figure 12 on page 20. The number of times pulses which are blanked
(subtracted, negative calibration) or split (added, positive calibration) depends upon the
value loaded into the five Calibration bits found in the Control Register. Adding counts
speeds the clock up, subtracting counts slows the clock down.
The Calibration bits occupy the five lower order bits (D4-D0) in the Control Register
(7FF8h). These bits can be set to represent any value between 0 and 31 in binary form. Bit
D5 is a Sign Bit; '1' indicates positive calibration, '0' indicates negative calibration.
Calibration occurs within a 64 minute cycle. The first 62 minutes in the cycle may, once per
相關PDF資料
PDF描述
M41T256YMT7F REAL TIME CLOCK, PDSO44
M41T56MH6F REAL TIME CLOCK, PDSO28
M41T60Q6F 1 TIMER(S), REAL TIME CLOCK, QCC16
M44C510-P40 4-BIT, MROM, MICROCONTROLLER, PDIP40
M44C510D-XXX-DOW 4-BIT, MROM, MICROCONTROLLER
相關代理商/技術參數
參數描述
M41T256YMT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit 32K x8 SERIAL RTC
M41T256YMT7 功能描述:實時時鐘 Serial 256K (32Kx8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T256YMT7E 功能描述:實時時鐘 Serial 256K (32Kx8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T256YMT7F 功能描述:實時時鐘 Serial 256K (32Kx8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T256YMT7TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit 32K x8 SERIAL RTC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*