- 您現在的位置：買賣IC網 > PDF目錄359061 > M41T00 (意法半導體) Serial Access TIMEKEEPER PDF資料下載
參數資料
| 型號： | M41T00 |
| 廠商： | 意法半導體 |
| 英文描述： | Serial Access TIMEKEEPER |
| 中文描述： | 串行訪問計時 |
| 文件頁數： | 8/15頁 |
| 文件大?。?/td> | 99K |
| 代理商： | M41T00 |
M41T00
8/15
Figure 6. Serial Bus Data Transfer Sequence
Figure 7. Acknowledgment Sequence
AI00587
DATA
CLOCK
DATA LINE
STABLE
DATA VALID
START
CONDITION
CHANGE OF
DATA ALLOWED
STOP
CONDITION
AI00601
DATA OUTPUT
BY RECEIVER
DATA OUTPUT
BY TRANSMITTER
SCLK FROM
MASTER
START
CLOCK PULSE FOR
ACKNOWLEDGEMENT
1
2
8
9
MSB
LSB
CLOCK OPERATION
The eight byte clock register (see Table 3) is used
to both set the clock and to read the date and time
from the clock, in a binary coded decimal format.
Seconds, Minutes, and Hours are contained within
the first three registers. Bits D6 and D7 of clock
register 2 (Hours Register) contain the CENTURY
ENABLE Bit (CEB) and the CENTURY Bit (CB).
Setting CEB to a ’1’ will cause CB to toggle, either
from ’0’ to ’1’ or from ’1’ to ’0’ at the turn of the cen-
tury (depending upon its initial state). If CEB is set
to a ’0’, CB will not toggle. Bits D0 through D2 of
register 3 contain the Day (day of week). Registers
4, 5 and 6 contain the Date (day of month), Month
and Years. The final register is the Control Regis-
ter (this is described in the Clock Calibration sec-
tion). Bit D7 of register 0 contains the STOP Bit
(ST). Setting this bit to a ’1’ will cause the oscillator
to stop. If the device is expected to spend a signif-
icant amount of time on the shelf, the oscillator
may be stopped to reduce current drain. When re-
set to a ’0’ the oscillator restarts within one second.
The seven Clock Registers may be read one byte
at a time, or in a sequential block. The Control
Register (Address location 7) may be accessed in-
dependently. Provision has been made to assure
that a clock update does not occur while any of the
seven clock addresses are being read. If a clock
address is being read, an update of the clock reg-
isters will be delayed by 250ms to allow the read
to be completed before the update occurs. This
will prevent a transition of data during the read.
Note:
This 250ms delay affects only the clock reg-
ister update and does not alter the actual clock
time.
相關PDF資料 |
PDF描述 |
|---|---|
| M41T00M | Serial Access TIMEKEEPER |
| M41T0M | SERIAL REAL-TIME CLOCK |
| M41T0M6T | SERIAL REAL-TIME CLOCK |
| M41T0DS6F | SERIAL REAL-TIME CLOCK |
| M41T0DS6T | SERIAL REAL-TIME CLOCK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M41T00_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial real-time clock |
| M41T00AUD | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial real-time clock with audio |
| M41T00AUD_12 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial real-time clock (RTC) with audio |
| M41T00AUDD1E | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial real-time clock with audio |
| M41T00AUDD1F | 功能描述:實時時鐘 SERIAL RTC W/AUDIO RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。