參數資料
型號： M38B79MFH-XXXXFP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100
文件頁數： 98/112頁
文件大小： 1862K
代理商： M38B79MFH-XXXXFP
83
38B7 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
q Erase command
The erase command is executed by inputting command code 2016
in the first cycle and command code 2016 again in the second
cycle. The command code is latched into the internal command
___
latch at the rising edges of the WE input in the first cycle and in
the second cycle, respectively. The erase operation is initiated at
___
the rising edge of the WE input in the second cycle, and the
memory contents are collectively erased within 9.5 ms as mea-
sured by the internal timer. Note that data 0016 must be written to
all memory locations before executing the erase command.
Note: An erase operation is not completed by executing the erase
command once. Always be sure to execute an erase verify
command after executing the erase command. When the fail-
ure is found in this verification, the user must repeatedly ex-
ecute the erase command until the pass. Refer to Figure 90
for the erase flowchart.
Fig. 89 Input/output timings during erasing (verify data is output at the same timing as for read.)
q Erase verify command
The user must verify the contents of all addresses after complet-
ing the erase command. The microcomputer enters the erase
verify mode by inputting the verify address and command code
A016 in the first cycle. The address is internally latched at the fall-
___
ing edge of the WE input, and the command code is internally
___
latched at the rising edge of the WE input. When control signals
are input in the second cycle at the timing shown in Figure 89, the
M38B79FF outputs the contents of the specified address to the
external.
Note: If any memory location where the contents have not been
erased is found in the erase verify operation, execute the op-
eration of “erase
→ erase verify” over again. In this case,
however, the user does not need to write data 0016 to memory
locations before erasing.
Address
Erase
Erase verify
Verify
address
tWC
tCS
tRRW
tWP
tWPH
tWP
tDE
tDS
2016
A016
Dout
tDS
tDH
Verify data output
tDH
tVSC
tDS
tWP
tWRR
tCS
tCH
tAS
tAH
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VPPH
VPPL
CE
OE
WE
Data
VPP
相關PDF資料
PDF描述
M38C13M6-XXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64
M38C12M4-XXXHP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64
M38C13E6HP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP64
M38C13M6-XXXHP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64
M38C12M4-XXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
M38C13E6FP 功能描述:IC 740 MCU OTP 24K 64LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
M38C13E6HP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C13RLFS 制造商:Renesas Electronics Corporation 功能描述:EMULATION MCU/8BIT CMOS EMULATION CHIP - Bulk
M38C24M4-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C24M4-XXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*