- 您現在的位置：買賣IC網 > PDF目錄370954 > M38867E8AFS (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38867E8AFS |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 69/110頁 |
| 文件大?。?/td> | 1601K |
| 代理商： | M38867E8AFS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁當前第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁
69
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
G
Program command
The microcomputer enters the program mode by inputting com-
mand code “40
16
” in the first cycle. The command code is latched
into the internal command latch at the rising edge of the WE input.
When the address which indicates a program location and data is
input in the second cycle, the M38869FFAHP/GP internally
latches the address at the falling edge of the WE input and the
data at the rising edge of the WE input. The M38869FFAHP/GP
starts programming at the rising edge of the WE input in the sec-
ond cycle and finishes programming within 10
μ
s as measured by
its internal timer. Programming is performed in units of bytes.
Note:
A programming operation is not completed by executing the
program command once. Always be sure to execute a pro-
gram verify command after executing the program command.
When the failure is found in this verification, the user must re-
peatedly execute the program command until the pass. Refer
to Figure 71 for the programming flowchart.
G
Program verify command
The microcomputer enters the program verify mode by inputting
command code “C0
16
” in the first cycle. This command is used to
verify the programmed data after executing the program com-
mand. The command code is latched into the internal command
latch at the rising edge of the WE input. When control signals are
input in the second cycle at the timing shown in Figure 69, the
M38869FFAHP/GP outputs the programmed address’s contents to
the external. Since the address is internally latched when the pro-
gram command is executed, there is no need to input it in the
second cycle.
Fig. 69 Input/output timings during programming (Verify data is output at the same timing as for read.)
Address
Program
Program verify
Program
address
t
WC
t
CS
t
RRW
t
WP
t
WPH
t
WP
t
DP
t
DS
40
16
D
IN
C0
16
Dout
t
DS
t
DH
t
DH
Verify data output
t
DH
t
VSC
t
DS
t
WP
t
WRR
t
CS
t
CS
t
CH
t
CH
t
CH
t
AS
t
AH
V
IH
V
IL
V
IH
V
IL
V
IH
V
IL
V
IH
V
IL
V
IH
V
IL
V
PP
H
V
PP
L
CE
OE
WE
Data
V
PP
相關PDF資料 |
PDF描述 |
|---|---|
| M38867H8A-AO1HP | LJT 5C 5#16 PIN RECP |
| M38867M8A-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869FFAGP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38867M8A | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38867M8A-010HP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38867E8AHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38867E8A-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38867E8FS | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38867E8-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38867E9-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。