- 您現在的位置：買賣IC網 > PDF目錄45047 > M38588GCFP 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDSO42 PDF資料下載
參數資料
| 型號： | M38588GCFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDSO42 |
| 封裝： | 8.40 X 17.50 MM, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件頁數： | 52/77頁 |
| 文件大?。?/td> | 824K |
| 代理商： | M38588GCFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
Rev.1.10
Apr 3, 2006
page 56 of 75
REJ03B0139-0110
3858 Group
(2) Wait mode
If the WIT instruction is executed, the internal clock
φ stops at an
“H” level, but the oscillator does not stop. The internal clock
φ re-
starts at reset or when an interrupt is received. Since the oscillator
does not stop, normal operation can be started immediately after
the clock is restarted.
To ensure that the interrupts will be received to release the STP or
WIT state, their interrupt enable bits must be set to “1” before ex-
ecuting of the STP or WIT instruction.
When releasing the STP state, the prescaler 12 and timer 1 will
start counting the clock XIN divided by 16. Accordingly, set the timer
1 interrupt enable bit to “0” before executing the STP instruction.
sNotes
If you switch the mode between middle/high-speed and low-
speed, stabilize both XIN and XCIN oscillations. The sufficient
time is required for the sub-clock to stabilize, especially immedi-
ately after power on and at returning from the stop mode. When
switching the mode between middle/high-speed and low-speed,
set the frequency on condition that f(XIN) > 3
× f(XCIN).
When using the oscillation stabilizing time set after STP instruction
released bit set to “1”, evaluate time to stabilize oscillation of the
used oscillator and set the value to the timer 1 and prescaler 12.
CLOCK GENERATING CIRCUIT
The 3858 group has two built-in oscillation circuits. An oscillation cir-
cuit can be formed by connecting a resonator between XIN and XOUT
(XCIN and XCOUT). Use the circuit constants in accordance with the
resonator manufacturer’s recommended values. No external resistor
is needed between XIN and XOUT since a feed-back resistor exists
on-chip.(An external feed-back resistor may be needed depending on
conditions.) However, an external feed-back resistor is needed be-
tween XCIN and XCOUT.
Immediately after power on, only the XIN oscillation circuit starts oscil-
lating, and XCIN and XCOUT pins function as I/O ports.
Frequency Control
(1) Middle-speed mode
The internal clock
φ is the frequency of XIN divided by 8. After re-
set is released, this mode is selected.
(2) High-speed mode
The internal clock
φ is half the frequency of XIN.
(3) Low-speed mode
The internal clock
φ is half the frequency of XCIN.
(4) Low power dissipation mode
The low power consumption operation can be realized by stopping
the main clock XIN in low-speed mode. To stop the main clock, set
bit 5 of the CPU mode register to “1”. When the main clock XIN is
restarted (by setting the main clock stop bit to “0”), set sufficient
time for oscillation to stabilize.
The sub-clock XCIN-XCOUT oscillating circuit can not directly input
clocks that are generated externally. Accordingly, make sure to
cause an external resonator to oscillate.
Oscillation Control
(1) Stop mode
If the STP instruction is executed, the internal clock
φ stops at an
“H” level, and XIN and XCIN oscillation stops. When the oscillation
stabilizing time set after STP instruction released bit (bit 0 of
address 003816) is “0”, the prescaler 12 is set to “FF16” and timer
1 is set to “0116”. When the oscillation stabilizing time set after
STP instruction released bit is “1”, set the sufficient time for oscil-
lation of used oscillator to stabilize since nothing is set to the
prescaler 12 and timer 1.
After STP instruction is released, the input of the prescaler 12 is
connected to count source which had set at executing the STP in-
struction, and the output of the prescaler 12 is connected to timer
1. Oscillator restarts when an external interrupt is received, but the
internal clock
φ is not supplied to the CPU (remains at “H”) until
timer 1 underflows. The internal clock
φ is supplied for the first
time, when timer 1 underflows. This ensures time for the clock os-
cillation using the ceramic resonators to be stabilized. When the
oscillator is restarted by reset, apply “L” level to the RESET pin
until the oscillation is stable since a wait time will not be gener-
ated.
Fig. 56 Ceramic resonator circuit
Fig. 57 External clock input circuit
XCIN
XCOUT
XIN
XOUT
CIN
COUT
CCIN
CCOUT
Rf
Rd
Rd (Note)
Notes : Insert a damping resistor if required.
The resistance will vary depending on the oscillator and
the oscillation drive capacity setting.
Use the value recommended by the maker of the
oscillator.
Also, if the oscillator manufacturer's data sheet
specifies that a feedback resistor be added external to
the chip though a feedback resistor exists on-chip,
insert a feedback resistor between XIN and XOUT
following the instruction.
XCIN
XCOUT
XIN
XOUT
CCIN
CCOUT
Rf
Rd
Open
External oscillation
circuit
Vcc
Vss
相關PDF資料 |
PDF描述 |
|---|---|
| M38749EFT | 8-BIT, OTPROM, 6.4 MHz, MICROCONTROLLER, PQFP80 |
| M38747M4T | 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80 |
| M38747M6T | 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80 |
| M38747M8T | 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80 |
| M38747MCF | 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38588GCFP#U0 | 功能描述:IC 740/3858 MCU QZ-ROM 42SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| M38588GCSP#U0 | 功能描述:IC 740/3858 MCU QZ-ROM 42DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| M3860 | 功能描述:電纜固定件和配件 FLEX LTSCG 500 RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度: |
| M3860 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 30COND 14AWG BLK 1000' |
| M3860 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 30COND 14AWG BLK 500' |
發布緊急采購，3分鐘左右您將得到回復。