參數資料
型號： M38588GCFP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDSO42
封裝： 8.40 X 17.50 MM, 0.80 MM PITCH, PLASTIC, SSOP-42
文件頁數： 49/77頁
文件大?。?/td> 824K
代理商： M38588GCFP
Rev.1.10
Apr 3, 2006
page 53 of 75
REJ03B0139-0110
3858 Group
WATCHDOG TIMER
The watchdog timer gives a mean of returning to the reset status
when a program cannot run on a normal loop (for example, be-
cause of a software run-away). The watchdog timer consists of an
8-bit watchdog timer L and an 8-bit watchdog timer H.
Initial Value of Watchdog Timer
At reset or writing to the watchdog timer control register (address
003916), each of watchdog timer H and L is set to “FF16”. Any in-
struction which generates a write signal such as the instructions of
STA, LDM, CLB and others can be used to write. The data of bits
6 and 7 are only valid when writing to the watchdog timer control
register. Each of watchdog timer is set to “FF16” regardless of the
written data of bits 0 to 5.
Operation of Watchdog Timer
The watchdog timer stops at reset and starts to count down by
writing to the watchdog timer control register. An internal reset oc-
curs at an underflow of the watchdog timer H. The reset is
released after waiting for a reset release time and the program is
processed from the reset vector address. Accordingly, program-
ming is usually performed so that writing to the watchdog timer
control register may be started before an underflow of the watch-
dog timer H. If writing to the watchdog timer control register is not
performed once, the watchdog timer does not function.
Fig. 52 Structure of Watchdog timer control register
Fig. 51 Block diagram of Watchdog timer
XIN
Data bus
XCIN
“10”
“00”
“01”
Main clock division
ratio selection bits
(Note)
“0”
“1”
1/16
Watchdog timer H count
source selection bit
Reset
circuit
STP instruction function selection bit
Watchdog timer H (8)
“FF16” is set when
watchdog timer
control register is
written to.
Internal reset
RESET
Watchdog timer L (8)
Note: Any one of high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register.
STP instruction
“FF16” is set when
watchdog timer
control register is
written to.
b0
STP instruction function selection bit
0: Entering Stop mode by execution of STP instruction
1: Internal reset by execution of STP instruction
Watchdog timer H count source selection bit
0: Watchdog timer L underflow
1: f(XIN)/16 or f(XCIN)/16
Watchdog timer H (for read-out of high-order 6 bit)
Watchdog timer control register
(WDTCON : address 003916)
b7
Bit 6 of Watchdog Timer Control Register
When bit 6 of the watchdog timer control register is “0”, the MCU
enters the stop mode by execution of STP instruction. Just after
releasing the stop mode, the watchdog timer restarts counting
(Note). When executing the WIT instruction, the watchdog timer
does not stop.
When bit 6 is “1”, execution of STP instruction causes an internal
reset. When this bit is set to “1” once, it cannot be rewritten to “0”
by program. Bit 6 is “0” at reset.
The necessary time after writing to the watchdog timer control reg-
ister to an underflow of the watchdog timer H is shown as follows.
When bit 7 of the watchdog timer control register is “0”:
32 s at XCIN = 32.768 kHz frequency and
65.536 ms at XIN = 16 MHz frequency.
When bit 7 of the watchdog timer control register is “1”:
125 ms at XCIN = 32.768 kHz frequency and
256
s at XIN = 16 MHz frequency.
Note: The watchdog timer continues to count for waiting for a stop mode re-
lease time. Do not generate an underflow of the watchdog timer H
during that time.
相關PDF資料
PDF描述
M38749EFT 8-BIT, OTPROM, 6.4 MHz, MICROCONTROLLER, PQFP80
M38747M4T 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80
M38747M6T 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80
M38747M8T 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80
M38747MCF 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
M38588GCFP#U0 功能描述:IC 740/3858 MCU QZ-ROM 42SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR)
M38588GCSP#U0 功能描述:IC 740/3858 MCU QZ-ROM 42DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR)
M3860 功能描述:電纜固定件和配件 FLEX LTSCG 500 RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M3860 BK001 制造商:Alpha Wire Company 功能描述:CBL 30COND 14AWG BLK 1000'
M3860 BK002 制造商:Alpha Wire Company 功能描述:CBL 30COND 14AWG BLK 500'
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*