- 您現在的位置：買賣IC網 > PDF目錄67763 > M38039FFLHP 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | M38039FFLHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 119/121頁 |
| 文件大?。?/td> | 2071K |
| 代理商： | M38039FFLHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁當前第119頁第120頁第121頁
Rev.1.01
Jan 25, 2008
Page 95 of 117
REJ03B0212-0101
3803 Group (Spec.L)
NOTES ON PERIPHERAL FUNCTIONS
Notes on Input and Output Ports
1. Notes in standby state
In standby state*1 for low-power dissipation, do not make input
levels of an I/O port “undefined”. Even when an I/O port of
Nchannel open-drain is set as output mode, if output data is “1”,
the aforementioned notes are necessary.
Pull-up (connect the port to VCC) or pull-down (connect the port
to VSS) these ports through a resistor.
When determining a resistance value, note the following points:
External circuit
Variation of output levels during the ordinary operation
When using built-in pull-up resistor, note on varied current
values:
When setting as an input port : Fix its input level
When setting as an output port : Prevent current from flowing
out to external
<Reason>
Exclusive input ports are always in a high-impedance state. An
output transistor becomes an OFF state when an I/O port is set as
input mode by the direction register, so that the port enter a
highimpedance state. At this time, the potential which is input to
the input buffer in a microcomputer is unstable in the state that
input levels are “undefined”. This may cause power source
current.
Even when an I/O port of N-channel open-drain is set as output
mode by the direction register, if the contents of the port latch is
“1”, the same phenomenon as that of an input port will occur.
*1 Standby state :
stop mode by executing STP instruction
wait mode by executing WIT instruction
2. Modifying output data with bit managing instruction
When the port latch of an I/O port is modified with the bit
managing instruction*1, the value of the unspecified bit may be
changed.
<Reason>
I/O ports are set to input or output mode in bit units. Reading
from a port register or writing to it involves the following
operations.
Port in input mode
Read: Read the pin level.
Write: Write to the port latch.
Port in output mode
Read: Read the port latch or read the output from the peripheral
function (specifications differ depending on the port).
Write: Write to the port latch. (The port latch value is output
from the pin.)
Since bit managing instructions*1 are read-modify-write
instructions,*2 using such an instruction on a port register causes
a read and write to be performed simultaneously on the bits other
than the one specified by the instruction.
When an unspecified bit is in input mode, its pin level is read and
that value is written to the port latch. If the previous value of the
port latch differs from the pin level, the port latch value is changed.
If an unspecified bit is in output mode, the port latch is generally
read. However, for some ports the peripheral function output is
read, and the value is written to the port latch. In this case, if the
previous value of the port latch differs from the peripheral
function output, the port latch value is changed.
*1 Bit managing instructions: SEB and CLB instructions
*2 Read-modify-write instructions: Instructions that read memory
in byte units, modify the value, and then write the result to the
same location in memory in byte units
Termination of Unused Pins
1. Terminate unused pins
(1) Output ports : Open
(2) I/O ports :
Set the I/O ports for the input mode and connect them to VCC
or VSS through each resistor of 1 k
to 10 k.
Ports that permit the selecting of a built-in pull-up resistor can
also use this resistor. Set the I/O ports for the output mode and
open them at “L” or “H”.
When opening them in the output mode, the input mode of the
initial status remains until the mode of the ports is switched
over to the output mode by the program after reset. Thus, the
potential at these pins is undefined and the power source
current may increase in the input mode. With regard to an
effects on the system, thoroughly perform system evaluation
on the user side.
Since the direction register setup may be changed because of a
program runaway or noise, set direction registers by program
periodically to increase the reliability of program.
(3) The AVSS pin when not using the A/D converter :
When not using the A/D converter, handle a power source pin
for the A/D converter, AVSS pin as follows:
AVSS: Connect to the VSS pin.
2. Termination remarks
(1) I/O ports :
Do not open in the input mode.
<Reason>
The power source current may increase depending on the
firststage circuit.
An effect due to noise may be easily produced as compared
with proper termination (2) in 1 and shown on the above.
(2) I/O ports :
When setting for the input mode, do not connect to VCC or VSS
directly.
<Reason>
If the direction register setup changes for the output mode
because of a program runaway or noise, a short circuit may occur
between a port and VCC (or VSS).
(3) I/O ports :
When setting for the input mode, do not connect multiple ports in
a lump to VCC or VSS through a resistor.
<Reason>
If the direction register setup changes for the output mode
because of a program runaway or noise, a short circuit may occur
between ports.
At the termination of unused pins, perform wiring at the
shortest possible distance (20 mm or less) from micro-
computer pins.
相關PDF資料 |
PDF描述 |
|---|---|
| M38039FFLWG | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PBGA64 |
| M38039MFL-XXXKP | 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PQFP64 |
| M38039FFLSP | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PDIP64 |
| M38039FFLKP | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PQFP64 |
| M38049FFLWG | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PBGA64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38039FFLHP#U0 | 功能描述:IC 3803 MCU FLASH 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38039FFLKP#U0 | 制造商:Renesas 功能描述:MCU 8-bit 740 CISC 60KB Flash 3.3V/5V 64-Pin LQFP Tray |
| M38039FFLKPU0 | 制造商:Renesas Electronics Corporation 功能描述:8bit MCU,3803,61K ProgROM,2K RAM,LQFP64 |
| M38039FFSP | 制造商:Mitsubishi Electric 功能描述:8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PDIP64 |
| M38039G4HHP#U0 | 功能描述:IC 740/3803 MCU QZROM 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。