- 您現在的位置：買賣IC網 > PDF目錄45037 > M37754M8C-XXXHP 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M37754M8C-XXXHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 0.50 MM PITCH, FINE PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 65/114頁 |
| 文件大小： | 1116K |
| 代理商： | M37754M8C-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
MITSUBISHI MICROCOMPUTERS
M37754M8C-XXXGP, M37754M8C-XXXHP
M37754S4CGP, M37754S4CHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
54
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
____
Once transmission has started, the TEi flag, TIi flag, and CTSi signal
____
(if CTSi input is selected ) are ignored until data transmission is com-
pleted.
Therefore, transmission does not stop until it completes event if the
TEi flag is cleared during transmission.
The transmission start condition indicated by TEi flag, TIi flag, and
____
CTSi is checked while the TENDi signal shown in Figure 65 is “H”.
Therefore, data can be transmitted continuously if the next transmis-
sion data is written in the transmit buffer register and TIi flag is
cleared to “0” before the TENDi signal goes “H”.
Bit 3 (TXEPTYi flag) of UARTi Transmit/Receive control register 0
changes to “1” at the next cycle just after the TENDi signal goes “H”
and changes to “0” when transmission starts. Therefore, this flag can
be used to determine whether data transmission is completed.
When the TIi flag changes from “0” to “1”, the interrupt request bit of
the UARTi transmit interrupt control register is set to “1”.
Transmission
Transmission is started when bit 0 (TEi flag) of UARTi Transmit/Re-
____
ceive control register 1 is “1”, bit 1 (TIi flag) is “0”, and CTSi input is
____
“L” if CTSi input is selected. As shown in Figures 65 and 66, data is
output from the TXDi pin with the stop bit or parity bit specified by bits
4 to 6 of UARTi Transmit/Receive mode register. The data is output
from the least significant bit.
The TIi flag indicates whether the transmit buffer is empty or not. It is
cleared to “0” when data is written in the transmit buffer, and is set to
“1” when the contents of the transmit buffer register is transferred to
the transmit register.
When the transmit register becomes empty after the contents has
been transmitted, data is transferred automatically from the transmit
buffer register to the transmit register if the next transmit start condi-
tion is satisfied.
Fig. 65 Transmit timing example when 8-bit asynchronous communication with parity and 1 stop bit selected
Fig. 66 Transmit timing example when 9-bit asynchronous communication with no parity and 2 stop bits selected
(1/Pfi or 1/fEXT)
× (n + 1) × 16
Written in transmit buffer register
Transmission clock
TEi
TIi
CTSi
TENDi
TXDi
TXEPTYi
D0 D1
ST
Start bit
Parity bit Stop bit
D2 D3 D4 D5 D6 D7
PSP ST D0 D1 D2 D3 D4 D5 D6 D7
PSP
ST D0 D1
Transmit register
← Transmit
buffer register
Stopped because TEi = “0”
(1/Pfi or 1/fEXT)
× (n + 1) × 16
Written in transmit buffer register
Transmission clock
TEi
TIi
TENDi
TXDi
TXEPTYi
D0 D1
ST
D2 D3 D4 D5 D6 D7 D8
SP
ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SP SP
ST D0
D2
D1
Transmit register
← Transmit
buffer register
Stopped because TEi = “0”
Start bit
Stop bit
相關PDF資料 |
PDF描述 |
|---|---|
| M37754S4CHP | 16-BIT, 40 MHz, MICROCONTROLLER, PQFP100 |
| M37754S4CHP | 16-BIT, 40 MHz, MICROCONTROLLER, PQFP100 |
| M37754M8C-XXXGP | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100 |
| M37777E9AGS | 16-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CQCC100 |
| M34550M6A-XXXFP | 4-BIT, MROM, 1.6 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37754S4CGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
| M37754S4CHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M3775PR-H400CL | 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR |
| M3775RK-0.75A | 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR |
| M3775RK-C0.50A | 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR |
發布緊急采購，3分鐘左右您將得到回復。