- 您現在的位置：買賣IC網 > PDF目錄45037 > M37754M8C-XXXHP 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M37754M8C-XXXHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 0.50 MM PITCH, FINE PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 35/114頁 |
| 文件大小： | 1116K |
| 代理商： | M37754M8C-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
27
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
MITSUBISHI MICROCOMPUTERS
M37754M8C-XXXGP, M37754M8C-XXXHP
M37754S4CGP, M37754S4CHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
(2) Event counter mode [01]
Figure 23 shows the bit configuration of the timer Ai mode register
during event counter mode. In event counter mode, bit 0 of the timer
Ai mode register must be “1” and bits 1 and 5 must be “0”.
The input signal from the TAiIN pin is counted when the count start bit
shown in Figure 19 is “1” and counting is stopped when it is “0”.
Count is performed at the fall of the input signal when bit 3 is “0” and
at the rise of the signal when it is “1”.
In event counter mode, whether to increment or decrement the count
can be selected with the up-down bit or the input signal from the
TAiOUT pin.
When bit 4 of the timer Ai mode register is “0”, the up-down bit is used
to determine whether to increment or decrement the count (decre-
ment when the bit is “0” and increment when it is “1”). Figure 24
shows the bit configuration of the up-down register.
When bit 4 of the timer Ai mode register is “1”, the input signal from
the TAiOUT pin is used to determine whether to increment or decre-
ment the count. However, note that bit 2 must be “0” if bit 4 is “1.” It is
because if bit 2 is “1”, TAiOUT pin becomes an output pin to output
pulses.
The count is decremented when the input signal from the TAiOUT pin
is “L” and incremented when it is “H”. Determine the level of the input
signal from the TAiOUT pin before a valid edge is input to the TAiIN pin.
An interrupt request signal is generated and the interrupt request bit
in the timer Ai interrupt control register is set when the counter
reaches 000016 (decrement count) or FFFF16 (increment count). At
the same time, the contents of the reload register is transferred to the
counter and the count is continued.
When bit 2 is “1,” each time the counter reaches 000016 (decrement
count) or FFFF16(increment count), the waveform’s polarity is re-
versed and is output from TAiOUT pin.
If bit 2 is “0”, TAiOUT pin can be used as a normal port pin.
However, if bit 4 is “1” and the TAiOUT pin is used as an output pin,
the output from the pin changes the count direction. Therefore, bit 4
must be “0” unless the output from the TAiOUT pin is to be used to se-
lect the count direction.
Fig. 23
Timer Ai mode register bit configuration during event
counter mode
Fig. 24 Up-down register bit configuration
76543210
1
0
×
0 1 : Always “01” in event counter mode
0 : No pulse output
1 : Pulse output
0 : Count at the falling edge of input signal
1 : Count at the rising edge of input signal
0 : Increment or decrement according
to up/down flag
1 : Increment or decrement according
to TAiOUT pin input signal level
0 : Always “0” in event counter mode
× × : Not used in event counter mode
Timer A0 mode register
Timer A1 mode register
Timer A2 mode register
Timer A3 mode register
Timer A4 mode register
Addresses
5616
5716
5816
5916
5A16
Timer A0 up-down bit
Timer A1 up-down bit
Timer A2 up-down bit
Timer A3 up-down bit
Timer A4 up-down bit
Timer A2 two-phase pulse signal
processing select bit
0 : Two-phase pulse signal processing
disabled
1 : Two-phase pulse signal processing
mode
Timer A3 two-phase pulse signal
processing select bit
0 : Two-phase pulse signal processing
disabled
1 : Two-phase pulse signal processing
mode
Timer A4 two-phase pulse signal
processing select bit
0 : Two-phase pulse signal processing
disabled
1 : Two-phase pulse signal processing
mode
Up-down register
76543210
Address
4416
相關PDF資料 |
PDF描述 |
|---|---|
| M37754S4CHP | 16-BIT, 40 MHz, MICROCONTROLLER, PQFP100 |
| M37754S4CHP | 16-BIT, 40 MHz, MICROCONTROLLER, PQFP100 |
| M37754M8C-XXXGP | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100 |
| M37777E9AGS | 16-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CQCC100 |
| M34550M6A-XXXFP | 4-BIT, MROM, 1.6 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37754S4CGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
| M37754S4CHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M3775PR-H400CL | 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR |
| M3775RK-0.75A | 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR |
| M3775RK-C0.50A | 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING RESISTOR |
發布緊急采購，3分鐘左右您將得到回復。