參數資料
型號： M37733MHBXXXFP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80
封裝： 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80
文件頁數： 41/92頁
文件大?。?/td> 1725K
代理商： M37733MHBXXXFP
43
MITSUBISHI MICROCOMPUTERS
M37733MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINARY
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
(3) Single sweep mode
Single sweep mode is selected when bit 3 of A-D control register 0 is
“0” and bit 4 is “1”.
In the single sweep mode, the number of analog input pins to be
swept can be selected. Analog input pins are selected by bits 1 and
0 of the A-D control register 1 (address 1F16). Two pins, four pins, six
pins or eight pins can be selected as analog input pins, depending
on the contents of these bits.
A-D conversion is performed only for selected input pins. After A-D
conversion is performed for input of AN0 pin, the conversion result is
stored in A-D register 0, and in the same way, A-D conversion is
performed for selected pins one after another. After A-D conversion
is performed for all selected pins, the sweep is stopped.
A-D conversion can be started with a software trigger or with an
external trigger input. A software trigger is selected when bit 5 is “0”
and an external trigger is selected when it is “1”.
When a software trigger is selected, A-D conversion is started when
A-D control register 0 bit 6 (A-D conversion start flag) is set to “1”.
When A-D conversion of all selected pins ends, an interrupt request
bit of the A-D conversion interrupt control register is set to “1”. At the
same time, A-D conversion start flag is cleared and A-D conversion
stops.
If an external trigger is selected, A-D conversion starts when the A-D
conversion start flag is “1” and the ADTRG input changes from “H” to
“L”. In this case, the A-D conversion result which is stored in the A-D
register 5 becomes invalid because the ADTRG pin is also used as the
AN5 pin.
The operation by external trigger is the same as that done by software
trigger except that the A-D conversion start flag is not cleared after
A-D conversion and a retrigger can be available during A-D
conversion.
(4) Repeat sweep mode
Repeat sweep mode 0 is selected when bit 3 of A-D control register
0 is “1” and bit 4 is “1”.
The difference from the single sweep mode is that A-D conversion
does not stop after converting from the AN0 pin to the selected pins,
but repeats again from the AN0 pin. The repeat is performed among
the selected pins. Also, no interrupt request is generated. Furthermore,
if software trigger is selected, the A-D conversion start flag is not
cleared. The A-D register can be read at any time.
相關PDF資料
PDF描述
M37733S4LHP 16-BIT, 12 MHz, MICROCONTROLLER, PQFP80
M37734M8LXXXHP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
M37735M4BXXXFP 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80
M37735MHBXXXFP 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80
M37735MHLXXXHP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
M37733MHL 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHLXXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733S4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER
M37733S4BFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER
M37733S4LHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*