- 您現在的位置：買賣IC網 > PDF目錄67763 > M37643F8HP 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M37643F8HP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 12 X 12 MM, 0.50 MM PITCH, PLASTIC, LQFP-80 |
| 文件頁數： | 58/120頁 |
| 文件大?。?/td> | 1253K |
| 代理商： | M37643F8HP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
42
7643 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to
change.
USB Transmission
Endpoint 0 to Endpoint 2 have IN (transmit) FIFOs individually.
Each endpoint’s FIFO is configured in following way:
Endpoint 0: 16-byte
Endpoint 1: 128-byte
Endpoint 2: Mode 0: 32-byte
Mode 1: 128-byte
When Endpoint 2 is used for data transmit, the IN FIFO size can
be selected. Endpoint 2 have 2 modes programmable IN-FIFO.
Each mode can be selected by the USB endpoint FIFO mode se-
lection register (address 005F16).
When writing data to the USB Endpoint-x FIFO (addresses 006016
to 006216) in the SFR area, the internal write pointer for the IN
FIFO is automatically increased by 1. When the AUTO_SET bit is
“1” and if the stored data reaches to the max. packet value set in
USB Endpoint x IN max. packet size register (address 005B16),
the USB FCU sets the IN_PKT_RDY bit to “1”. When the
AUTO_SET bit is “0”, the IN_PKT_RDY bit will not be automati-
cally set to “1”; it must be set to “1” by software. (The AUTO_SET
bit function is not applicable to Endpoint 0.)
The USB FCU transmits the data when it receives the next IN to-
ken. The IN_PKT_RDY bit automatically goes to “0” when the data
transfer is complete.
qInterrupt transfer mode
Endpoints 1 to 2 can be used in interrupt transfer mode. During a
regular interrupt transfer, an interrupt transaction is similar to the
bulk transfer. Therefore, there is no special setting required. When
IN-endpoint is used for a rate feedback interrupt transfer, INTPT
bit of the IN_CSR register must be set to “1”. The following steps
show how to configure the IN-endpoint for the rate feedback inter-
rupt transfer.
1. Set a value which is larger than 1/2 of the USB Endpoint-x FIFO
size to the USB Endpoint x IN max. package size register.
2. Set INTPT bit to “1”.
3. Flush the old data in the FIFO.
4. Store transmission data to the IN FIFO and set the
IN_PKT_RDY bit to “1”.
5. Repeat steps 3 and 4.
In a real application, the function-side always has transfer data
when the function sends an endpoint in a rate feedback interrupt.
Accordingly, the USB FCU never returns a NAK against the host
IN token for the rate feedback interrupt. The USB FCU always
transmits data in the FIFO in response to an IN token, regardless
of IN_PKT_RDY. However, this premises that there is always an
ACK response from Host PC after the 7643 Group has transmitted
data to IN token.
When MAXP size
≤ (a half of IN FIFO size), the IN FIFO can store
two packets (called double buffer). At this time, the IN FIFO sta-
tus can be checked by monitoring the IN_PKT_RDY bit and the
TX_NOT_EPT flag. The TX_NOT_EPT flag is a read-only flag
which shows the FIFO state. When IN_PKY_RDY = 0 and
TX_NOT_EPT = 0, IN FIFO is empty. When IN_PKY_RDY = 0 and
TX_NOT_EPT = 1, IN FIFO has one packet.
In double buffer mode, as long as the IN FIFO is not filled with
double packets, IN_PKT_RDY will not be set to “1”, even if it is set
to “1” by software, but TX_NOT_EPT flag will be set to “1”. In
single buffer mode, if MAXP > (a half of IN FIFO), this condition
never occurs.
When IN_PKT_RDY = “1” and TX_NOT_EPT = “1”, IN FIFO holds
two packets in double buffer mode and one packet in single
packet mode. In single packet mode, when the IN_PKT_RDY bit is
set to “1” by software, the TX_NOT_EPT flag is set to “1” as well.
During double buffer mode, if you want to load two packets se-
quentially, you must set the IN_PKT_RDY bit to “1” each time a
packet is loaded.
相關PDF資料 |
PDF描述 |
|---|---|
| M37643M8-XXXHP | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37702S1LGP | 16-BIT, 8 MHz, MICROCONTROLLER, PQFP80 |
| M37702M2LXXXGP | 16-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80 |
| M37702M2LXXXHP | 16-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80 |
| M37703MDBSP | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PDIP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37643F8M8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37643M8E8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37643M8M8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M3764A-12 | 制造商:OK International 功能描述: |
| M3765 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HORN/SIREN WITH SOFT CHIRP 6 ALARM SOUNDS |
發布緊急采購，3分鐘左右您將得到回復。