- 您現在的位置：買賣IC網 > PDF目錄69011 > M34556G8HFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42 PDF資料下載
參數資料
| 型號： | M34556G8HFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| 封裝： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件頁數： | 79/147頁 |
| 文件大小： | 1087K |
| 代理商： | M34556G8HFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁當前第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁
Rev.3.02
Dec 22, 2006
page 35 of 142
REJ03B0025-0302
4556 Group
(7) Timer input/output pin
(C/CNTR pin)
CNTR pin is used to input the timer 1 count source and output the
PWM signal generated by timer 2. When the PWM signal is output
from C/CNTR pin, set “0” to the output latch of port C.
The selection of CNTR output signal can be controlled by bit 3 of
register W2.
When the CNTR input is selected for timer 1 count source, timer 1
counts the waveform of CNTR input selected by bit 0 of register
W4. Also, when the CNTR input is selected, the output of port C is
invalid (high-impedance state).
(8) Timer interrupt request flags (T1F, T2F, T3F)
Each timer interrupt request flag is set to “1” when each timer
underflows. The state of these flags can be examined with the skip
instructions (SNZT1, SNZT2, SNZT3).
Use the interrupt control register V1, V2 to select an interrupt or a
skip instruction.
An interrupt request flag is cleared to “0” when an interrupt occurs
or when the next instruction is skipped with a skip instruction.
(9) Count start synchronization circuit (timer 1)
Timer 1 has the count start synchronous circuit which synchronizes
the input of INT pin, and can start the timer count operation.
Timer 1 count start synchronous circuit function is selected by set-
ting the bit 0 of register I1 to “1” and the control by INT pin input
can be performed.
When timer 1 count start synchronous circuit is used, the count
start synchronous circuit is set, the count source is input to each
timer by inputting valid waveform to INT pin.
The valid waveform of INT pin to set the count start synchronous
circuit is the same as the external interrupt activated condition.
Once set, the count start synchronous circuit is cleared by clearing
the bit I10 to “0” or reset.
However, when the count auto-stop circuit is selected, the count
start synchronous circuit is cleared (auto-stop) at the timer 1 under-
flow.
(10) Count auto-stop circuit (timer 1)
Timer 1 has the count auto-stop circuit which is used to stop timer
1 automatically by the timer 1 underflow when the count start syn-
chronous circuit is used.
The count auto-stop cicuit is valid by setting the bit 3 of register W1
to “1”. It is cleared by the timer 1 underflow and the count source to
timer 1 is stopped.
This function is valid only when the timer 1 count start synchronous
circuit is selected.
(11) Precautions
Note the following for the use of timers.
Prescaler
Stop counting and then execute the TABPS instruction to read
from prescaler data.
Stop counting and then execute the TPSAB instruction to set
prescaler data.
Timer count source
Stop timer 1, 2, and LC counting to change its count source.
Reading the count value
Stop timer 1 or 2 counting and then execute the data read in-
struction (TAB1, TAB2) to read its data.
Writing to the timer
Stop timer 1, 2 or LC counting and then execute the data write in-
struction (T1AB, T2AB, TLCA) to write its data.
Writing to reload register R1, R2H
When writing data to reload register R1 or reload regiser R2H
while timer 1 or timer 2 is operating, avoid a timing when timer 1
or timer 2 underflows.
Timer 2
Avoid a timing when timer 2 underflows to stop timer 2 at PWM
output function used.
When “H” interval extension function of the PWM signal is set to
be “valid”, set “1” or more to reload register R2H.
Timer 3
Stop timer 3 counting to change its count source.
Timer input/output pin
Set the port C output latch to “0” to output the PWM signal from
C/CNTR pin.
相關PDF資料 |
PDF描述 |
|---|---|
| M34556M8-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M34556M8H-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M34556M4H-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M34559G6FP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP52 |
| M34559G6-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34556M4H-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34556M4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34556M8H-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34556M8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34556MXH-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。