- 您現在的位置：買賣IC網 > PDF目錄98005 > M34551E8-XXXFP 4-BIT, OTPROM, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | M34551E8-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, OTPROM, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 10 MM, 0.65 MM PITCH, PLASTIC, QFP-48 |
| 文件頁數： | 86/154頁 |
| 文件大小： | 1778K |
| 代理商： | M34551E8-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁
FUNCTIONAL BLOCK OPERATIONS
HARDWARE
1-26
4551 Group User’s Manual
Table 11 Carrier generating circuit control register and control flag
C20
Auto-control output by timer 1 is invalid
Auto-control output by timer 1 is valid
Carrier wave output auto-control bit
0
1
at reset : 02
Carrier wave output control register C2
at power down : 02
W
CR
Carrier wave generating stop (SPCR instruction)
Carrier wave generating start (STCR instruction)
Carrier wave generating control
0
1
at reset : 02
Carrier wave generating control flag CR
at power down : 02
W
Note: “W” represents write enabled.
(1) Carrier generating circuit related registers
q Carrier wave selection register C1
Each carrier waveform can be selected by setting the register
C1. Set the contents of this register through register A with
the TC1A instruction.
q Carrier wave output control register C2
Timer 1 can auto-control the output enable interval and the
output disable interval of the carrier wave output from port
CARR by setting the register C2. Set the contents of this
register through register A with the TC2A instruction.
The setting of the output enable/disable interval is described
below.
Validate the carrier wave output auto-control function
(C20=“1”).
Select the carrier wave or the carrier wave divided by 2
as the timer 1 count source.
Set the count value (the output enable interval of carrier
wave from port CARR) to timer 1.
Operate timer 1 (W20=“1”).
Operate the carrier generating circuit (STCR instruction
executed).
Set the next count value (the output disable interval of
carrier wave from port CARR) to reload register R1 before
timer 1 underflow occurs.
The carrier wave is output from port CARR until the first timer
1 underflow occurs. The output of the carrier wave from port
CARR is disabled and the next count value is loaded from
reload register R1 to timer 1 by the first timer 1 underflow.
Then, the output of carrier wave is disabled until the second
timer 1 underflow. Also, the next enable interval of the carrier
wave output can be set by setting the third count value to
timer 1 reload register before the second timer 1 underflow
occurs. If the carrier wave output auto-control function is
invalidated (C20=“0”) while the carrier wave output is auto-
controlled, the output of port CARR retains the state when
the auto-control is invalidated regardless of timer 1 underflow.
This state can be terminated by timer 1 stop (W20=“0”). When
the carrier wave output auto-control function is validated
(C20=“1”) again after it is invalidated (C20=“0”), the auto-
control of carrier wave output is started again when the next
timer 1 underflow occurs.
(2) Carrier wave generating control flag (CR)
The CR flag is used to control the carrier wave generating
operation of the carrier generating circuit. The CR flag is “1”
and the carrier wave generating is started by executing the
STCR instruction. The CR flag is “0” and the carrier wave
generating is stopped by executing the SPCR instruction. The
CR flag is “0” at system reset.
(3) Note on the carrier generating circuit stop
In order to stop the carrier wave which has the cycle longer
than that of the instruction clock with the SPCR instruction,
stop it at the point when the carrier wave outputs “L” level in
the SPCR instruction execution cycle.
If this condition is not satisfied, the last “H” output interval of
carrier wave is shortened.
(4) Notes when using the carrier wave output auto-control function
q Execute the STCR instruction after setting the timer 1 and
register C2 in order to start the carrier generating circuit
operation.
q Stop the timer 1 (W20=“0”) after stopping the carrier
generating circuit (SPCR instruction executed) while the
carrier wave output is disabled in order to stop the carrier
wave output auto-control operation.
q If the carrier wave output auto-control function is invalidated
(C20=“0”) while the carrier wave output is auto-controlled,
the output of port CARR retains the state when the auto-
control is invalidated regardless of timer 1 underflow. This
state can be terminated by timer 1 stop (W20=“0”).
When the carrier wave output auto-control function is
validated (C20=“1”) again after it is invalidated (C20=“0”),
the auto-control of carrier wave output is started again when
the next timer 1 underflow occurs. However, when the carrier
wave output auto-control bit is changed during timer 1
underflow, the error-operation may occur.
q Use the carrier wave or the carrier wave divided by 2 as the
timer 1 count source when the carrier wave output auto-
control function is selected.
If the ORCLK is used as the count source, a hazard may
occur in port CARR output because ORCLK is not
synchronized with the carrier wave.
q When “no carrier wave” is selected with register C1
((C13C12C11C10) = (0101), (1101)), the enable/disable of
the carrier wave output cannot be controlled by the carrier
wave output auto-control function.
相關PDF資料 |
PDF描述 |
|---|---|
| M34554M8-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64 |
| M34554MC-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64 |
| M34571G6FP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24 |
| M34584EDFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M35047-XXXSP | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34551M4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:4-BIT SINGLE-CHIP MICROCOMPUTER |
| M34551M4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTER |
| M34551M8 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:4-BIT SINGLE-CHIP MICROCOMPUTER |
| M34552G8FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34552G8HFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。