參數資料
型號: M34501M4-XXXFP
元件分類: 微控制器/微處理器
英文描述: 4-BIT, MROM, MICROCONTROLLER, PDSO20
封裝: 5.30 X 12.60 MM, 1.27 MM PITCH, PLASTIC, SOP-20
文件頁數: 61/116頁
文件大?。?/td> 859K
代理商: M34501M4-XXXFP
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
4501 Group
Rev.3.01
2005.02.07
page 49 of 112
REJ03B0104-0301
LIST OF PRECAUTIONS
Noise and latch-up prevention
Connect a capacitor on the following condition to prevent noise
and latch-up;
connect a bypass capacitor (approx. 0.1
F) between pins VDD
and VSS at the shortest distance,
equalize its wiring in width and length, and
use relatively thick wire.
In the One Time PROM version, CNVSS pin is also used as VPP
pin. Accordingly, when using this pin, connect this pin to VSS
through a resistor about 5 k
(connect this resistor to CNVSS/
VPP pin as close as possible).
Register initial values 1
The initial value of the following registers are undefined after sys-
tem is released from reset. After system is released from reset,
set initial values.
Register Z (2 bits)
Register D (3 bits)
Register E (8 bits)
Register initial values 2
The initial value of the following registers are undefined at RAM
back-up. After system is returned from RAM back-up, set initial
values.
Register Z (2 bits)
Register X (4 bits)
Register Y (4 bits)
Register D (3 bits)
Register E (8 bits)
Stack registers (SKS) and stack pointer (SP)
Stack registers (SKs) are eight identical registers, so that subrou-
tines can be nested up to 8 levels. However, one of stack
registers is used respectively when using an interrupt service
routine and when executing a table reference instruction. Accord-
ingly, be careful not to over the stack when performing these
operations together.
Prescaler
Stop the prescaler operation to change its frequency dividing ra-
tio.
Timer count source
Stop timer 1 or 2 counting to change its count source.
Reading the count value
Stop timer 1 or 2 counting and then execute the TAB1 or TAB2
instruction to read its data.
Writing to the timer
Stop timer 1 or 2 counting and then execute the T1AB or T2AB
instruction to write its data.
Writing to reload register R1
When writing data to reload register R1 while timer 1 is operat-
ing, avoid a timing when timer 1 underflows.
Watchdog timer
The watchdog timer function is valid after system is released
from reset. When not using the watchdog timer function, execute
the DWDT instruction and the WRST instruction continuously,
and clear the WEF flag to “0” to stop the watchdog timer function.
The watchdog timer function is valid after system is returned from
the RAM back-up. When not using the watchdog timer function,
execute the DWDT instruction and the WRST instruction continu-
ously every system is returned from the RAM back-up, and stop
the watchdog timer function.
Multifunction
The input/output of D2, D3, P12 and P13 can be used even when
C, K, CNTR (input) and INT are selected.
The input of P12 can be used even when CNTR (output) is selected.
The input/output of P20 and P21 can be used even when AIN0 and
AIN1 are selected.
Program counter
Make sure that the PCH does not specify after the last page of
the built-in ROM.
POF and POF2 instructions
When the POF or POF2 instruction is executed continuously af-
ter the EPOF instruction, system enters the RAM back-up state.
Note that system cannot enter the RAM back-up state when ex-
ecuting only the POF or POF2 instruction.
Be sure to disable interrupts by executing the DI instruction be-
fore executing the EPOF instruction and the POF or POF2
instruction continuously.
Fig. 48 Timer count start timing and count time when opera-
tion starts (T1, T2)
(1) Timer
Count Source
Timer Value
Timer Underflow
Signal
3
21
032
103
2
Count Source
(CNTR input)
(2)
(3)
(4)
10
11
12
13
14
Timer 1 and timer 2 count start timing and count time when
operation starts
Count starts from the first rising edge of the count source (2) af-
ter timer 1 and timer 2 operations start (1).
Time to first underflow (3) is shorter (for up to 1 period of the
count source) than time among next underflow (4) by the timing
to start the timer and count source operations after count starts.
When selecting CNTR input as the count source of timer 2, timer
2 operates synchronizing with the falling edge of CNTR input.
相關PDF資料
PDF描述
M34501E4FP 4-BIT, OTPROM, MICROCONTROLLER, PDSO20
M34502M2-XXXFP 4-BIT, MROM, MICROCONTROLLER, PDSO24
M34502M4-XXXFP 4-BIT, MROM, MICROCONTROLLER, PDSO24
M34506M4-XXXFP 4-BIT, MROM, MICROCONTROLLER, PDSO20
M34506E4FP 4-BIT, OTPROM, MICROCONTROLLER, PDSO20
相關代理商/技術參數
參數描述
M34502E4 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34502E4FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 4500 SERIES
M34502M2 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34502M2-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34502M4 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER