- 您現在的位置：買賣IC網 > PDF目錄358961 > LV320MH (Spansion Inc.) 32 Megabit (4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control PDF資料下載
參數資料
| 型號： | LV320MH |
| 廠商： | Spansion Inc. |
| 英文描述： | 32 Megabit (4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control |
| 中文描述： | 32兆位（4個M × 8位）的MirrorBit⑩3.0伏特，只有統一部門閃存記憶體與VersatileI /輸出⑩控制 |
| 文件頁數： | 30/61頁 |
| 文件大?。?/td> | 772K |
| 代理商： | LV320MH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
28
Am29LV033MU
September 12, 2006
D A T A S H E E T
Figure 5.
Program Operation
Program Suspend/Program Resume
Command Sequence
The Program Suspend command allows the system to
interrupt a programming operation or a Write to Buffer
programming operation so that data can be read from
any non-suspended sector. When the Program Sus-
pend command is written during a programming pro-
cess, the device halts the program operation within 15
μ
s maximum (5
μ
s typical) and updates the status bits.
Addresses are not required when writing the Program
Suspend command.
After the programming operation has been sus-
pended, the system can read array data from any
non-suspended sector. The Program Suspend com-
mand may also be issued during a programming oper-
ation while an erase is suspended. In this case, data
may be read from any addresses not in Erase Sus-
pend or Program Suspend. If a read is needed from
the SecSi Sector area (One-time Program area), then
user must use the proper command sequences to
enter and exit this region.
The system may also write the autoselect command
sequence when the device is in the Program Suspend
mode. The system can read as many autoselect codes
as required. When the device exits the autoselect
mode, the device reverts to the Program Suspend
mode, and is ready for another valid operation. See
Autoselect Command Sequence for more information.
After the Program Resume command is written, the
device reverts to programming. The system can deter-
mine the status of the program operation using the
DQ7 or DQ6 status bits, just as in the standard pro-
gram operation. See
Write Operation Status
for more
information.
The system must write the Program Resume com-
mand (address bits are don’t care) to exit the Program
Suspend mode and continue the programming opera-
tion. Further writes of the Resume command are ig-
nored. Another Program Suspend command can be
written after the device has resume programming.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data
No
Yes
Last Address
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
Note:
See Table 10 for program command sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| LV3400M | FM Multiplex Filter(FM多路濾波器) |
| LV3400 | FM Multiplex Filter |
| LV3403M | 3V Operation Filter for FM Multiplex Broadcasting Reception(用于FM多路廣播接收的3V運算濾波器) |
| LV4512V | LV4512V |
| LV549 | High Power Class B Output Stage |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LV320ML | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32 Megabit (4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control |
| LV320MT | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32 Megabit (4 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control |
| LV321 | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:SINGLE GENERAL PURPOSE, LOW VOLTAGE, RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIER |
| LV321_11 | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:SINGLE GENERAL PURPOSE, LOW VOLTAGE, RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIER |
| LV321G-AF5-R | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:SINGLE GENERAL PURPOSE, LOW VOLTAGE, RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。