參數資料
型號: LU3X54FT
廠商: Lineage Power
英文描述: Quad-FET (Fast Ethernet Transceiver) for 10Base-T/100Base-TX/FX(應用于10基數-T和100基數-TX/FX的四快速以太網收發器)
中文描述: 四場效應管(快速以太網收發器)的10Base-T/100Base-TX/FX(應用于10基數- T的和100基數-TX/FX的四快速以太網收發器)
文件頁數: 39/54頁
文件大?。?/td> 677K
代理商: LU3X54FT
Lucent Technologies Inc.
39
Data Sheet
July 2000
LU3X54FT
QUAD-FET for 10Base-T/100Base-TX/FX
MII Station Management
(continued)
Management Registers (MR)
(continued)
Table 22. MR31—Device-Specific Register 4 (Quick Status) Bit Descriptions
1. Note that the format for the bit descriptions is as follows: the first number is the register number, the second number is the bit position in the
register, and the name of the instantiated pad is in capital letters.
2 R = read; W = write.
Register/Bit
1
31.15 (ERROR)
Type
2
R
Description
Receiver Error.
When this bit is a 1, it indicates that a receive error has been
detected. This bit is valid in 100 Mbits/s only. This bit will remain set until cleared by
reading the register. Default is a 0.
False Carrier.
When bit [31.7] is set to 0 and this bit is a 1, it indicates that the carrier
detect state machine has found a false carrier. This bit is valid in 100 Mbits/s only. This
bit will remain set until cleared by reading the register. Default is 0.
Link Status Change.
When bit [31.7] is set to a 1, this bit is redefined to become the
LINK_STAT_CHANGE bit and goes high whenever there is a change in link status (bit
[31.11] changes state).
Remote Fault.
When this bit is a 1, it indicates a remote fault has been detected. This
bit will remain set until cleared by reading the register. Default is a 0.
Unlocked/Jabber.
If this bit is set when operating in 100 Mbits/s mode, it indicates
that the TX descrambler has lost lock. If this bit is set when operating in 10 Mbits/s
mode, it indicates a jabber condition has been detected. This bit will remain set until
cleared by reading the register.
Link Status.
When this bit is a 1, it indicates a valid link has been established. This bit
has a latching low function: a link failure will cause the bit to clear and stay cleared
until it has been read via the management interface.
Link Partner Pause.
When this bit is set to a 1, it indicates that the LU3X54FT wishes
to exchange flow control information.
Link Speed.
When this bit is set to a 1, it indicates that the link has negotiated to
100 Mbits/s. When this bit is a 0, it indicates that the link is operating at 10 Mbits/s.
Duplex Mode.
When this bit is set to a 1, it indicates that the link has negotiated to
full-duplex mode. When this bit is a 0, it indicates that the link has negotiated to half-
duplex mode.
Interrupt Configuration.
When this bit is set to a 0, it defines bit [31.14] to be the
RXERR_ST bit and the interrupt pin (MASK_STAT_INT) goes high whenever any of
bits [31.15:12] go high, or bit [31.11] goes low. When this bit is set high, it redefines
bit [31.14] to become the LINK_STAT_CHANGE bit, and the interrupt pin
(MASK_STAT_INT) goes high only when the link status changes (bit [31.14] goes
high). This bit defaults to 0.
Interrupt Mask.
When set high, no interrupt is generated by this channel under any
condition. When set low, interrupts are generated according to bit [31.7].
Lowest Autonegotiation State.
These 3 bits report the state of the lowest autonego-
tiation state reached since the last register read, in the priority order defined below:
000: Autonegotiation enable.
001: Transmit disable or ability detect.
010: Link status check.
011: Acknowledge detect.
100: Complete acknowledge.
101: FLP link good check.
110: Next-page wait.
111: FLP link good.
Highest Autonegotiation State.
These 3 bits report the state of the highest autone-
gotiation state reached since the last register read, as defined above for bit [31.5:3].
31.14 (RXERR_ST)/
(LINK_STAT_CHANGE)
R
31.13 (REM_FLT)
R
31.12 (UNLOCKED)/
(JABBER)
R
31.11 (LSTAT_OK)
R
31.10 (PAUSE)
R
31.9 (SPEED100)
R
31.8 (FULL_DUP)
R
31.7 (INT_CONF)
R/W
31.6 (INT_MASK)
R/W
31.5:3
(LOW_AUTO__STATE)
R
31.2:0
(HI_AUTO_STATE)
R
相關PDF資料
PDF描述
LU5X34F Quad Gigabit Ethernet Transceiver
LU5X34F Quad Gigabit Ethernet Transceiver(千兆位以太網四收發器)
LUCL8551AAU Subscriber Line Interface Circuit
LUCL8551AP Subscriber Line Interface Circuit
LUCL8560AAU Subscriber Line Interface Circuit
相關代理商/技術參數
參數描述
LU3X54FTL 制造商:AGERE 制造商全稱:AGERE 功能描述:QUAD-FET for 10Base-T/100Base-TX/FX
LU3X54FTLHS208 制造商:Alcatel-Lucent 功能描述:3X54FTLHS208
LU3X54FTL-HS208-DB 制造商:AGERE 制造商全稱:AGERE 功能描述:QUAD-FET for 10Base-T/100Base-TX/FX
LU3X54FTLHS208-DB 制造商:Alcatel-Lucent 功能描述:3X54FTLHS208-DB
LU400 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:NEMA Cabinet Legs