參數資料
型號: LTC4303CDD#TRPBF
廠商: Linear Technology
文件頁數: 8/12頁
文件大?。?/td> 549K
描述: IC BUS BUFFER I2C 8-DFN
產品培訓模塊: LTC4310 - Hot-Swappable I²C Isolators
標準包裝: 2,500
類型: 熱交換開關
應用: 通用型緩沖器/總線擴展器
內部開關:
電源電壓: 2.7 V ~ 5.5 V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 8-WFDFN 裸露焊盤
供應商設備封裝: 8-DFN-EP(3x3)
包裝: 帶卷 (TR)
LTC4303
8
4303fb
Resistor Pull-Up Selection
The system pull-up resistors must be strong enough
to provide a positive slew rate of 0.8V/祍 on the SDA
and SCL pins, in order to activate the rise time accelera-
tors during rising edges. Choose maximum resistor value
R
PULL-UP(MAX)
 using the formula:
where V
BUSMIN
 is the minimum operating pull-up sup-
ply voltage, and C
BUS
 the total capacitance on respec-
tive bus line.
 
R
k
V
V
ns V
C
pF
PULLUP MAX
BUS MIN
BUS
(
)
(    )
[    ]
  .
"
[   /  ]
[   ]
& =
(
)
0 8
1250
For example, assume V
BUS
 = V
CC
 = 3.3V, and assuming
?0% supply tolerance, V
BUSMIN
 = 2.97V. With C
BUS
=
100pF, R
PULL-UP, MAX
 = 27.1k. Therefore a smaller pull-up
resistor than 27.1k must be used, so 10k works  ne.
Live Insertion and Capacitance Buffering Application
Figures 3 through 6 illustrate applications of the LTC4303
that take advantage of both its Hot Swap
TM
 controlling and
capacitance buffering features. In all of these applications,
note that if the I/O cards were plugged directly into the
backplane without the LTC4303 buffer, all of the backplane
and card capacitances would add directly together, making
rise- and fall-time requirements dif cult to meet. Placing a
LTC4303 on the edge of each card, however, isolates the
card capacitance from the backplane. For a given I/O card,
the LTC4303 drives the capacitance on the card side and
the backplane must drive only the digital input capacitance
of the LTC4303, which is less than 10pF.
In most applications the LTC4303 will be used with a
staggered connector where V
CC
 and GND will be long
pins. SDA and SCL are medium length pins to ensure that
the V
CC
 and GND pins make contact  rst. This will allow
the precharge circuitry to be activated on SDA and SCL
before they make contact. ENABLE is a short pin that is
pulled down when not connected. This is to ensure that
the connection between the backplane and the cards data
and clock busses is not enabled until the transients as-
sociated with live insertion have settled.
Figure 3 shows the LTC4303 in a CompactPCI
TM
 con gu-
ration. Connect V
CC
 and ENABLE to the output of one of
the CompactPCI power supply Hot Swap circuits. Use a
pull-up resistor to ENABLE for a card side enable/disable.
V
CC
 is monitored by a  ltered UVLO circuit. With the V
CC
 
voltage powering up after all the other pins have established
connection, the UVLO circuit ensures that the backplane
and the card data and clock busses are not connected until
the transients associated with live insertion have settled.
Owing to their small capacitance, the SDAIN and SCLIN
pins cause minimal disturbance on the backplane busses
when they make contact with the connector.
Figure 4 shows the LTC4303 in a PCI application where all
of the pins have the same length. In this case, a RC  lter
circuit on the I/O card with a product of 10ms provides
a  lter to prevent the LTC4303 from becoming activated
until the transients associated with live insertion have
settled. Connect the capacitor between ENABLE and GND,
and the resistor from V
CC
 to ENABLE.
Hot Swap is a trademark of Linear Technology Corporation.
APPLICATIO  S I FOR  ATIO
U
U
U
相關PDF資料
PDF描述
LTC4304IDD#TRPBF IC BUS BUFFER I2C 10-DFN
LTC4307IMS8-1#TRPBF IC BUFFER 2-WIRE BUS 8-MSOP
LTC4307IMS8#TRPBF IC BUS BUFFER I2C 8-MSOP
LTC4308IMS8#TRPBF IC BUS BUFFER LV 8-MSOP
LTC4309IGN#TRPBF IC BUS BUFFER 2-WIRE 16-SSOP
相關代理商/技術參數
參數描述
LTC4303CMS8 制造商:Linear Technology 功能描述:Hot Swappable Bus Buffer 8-Pin MSOP
LTC4303CMS8#PBF 功能描述:IC BUS BUFFER I2C 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型,PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V,12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP(12x12) 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4303CMS8#PBF 制造商:Linear Technology 功能描述:IC HOT SWAP BUS BUFFER MSOP-8
LTC4303CMS8#TRPBF 功能描述:IC BUS BUFFER I2C 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統,AdvancedTCA ? 系統,高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP,10-MSOP(0.118",3.00mm 寬) 供應商設備封裝:10-MSOP 包裝:管件
LTC4303IDD#PBF 功能描述:IC BUS BUFFER I2C 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP(3x3) 包裝:管件