- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4303CDD#TRPBF (Linear Technology)IC BUS BUFFER I2C 8-DFN Datasheet資料下載
參數資料
| 型號： | LTC4303CDD#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 549K |
| 描述： | IC BUS BUFFER I2C 8-DFN |
| 產品培訓模塊： | LTC4310 - Hot-Swappable I²C Isolators |
| 標準包裝： | 2,500 |
| 類型： | 熱交換開關 |
| 應用： | 通用型緩沖器/總線擴展器 |
| 內部開關： | 是 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 8-DFN-EP（3x3） |
| 包裝： | 帶卷 (TR) |
LTC4303
6
4303fb
Start-Up
When the LTC4303 rst receives power on its V
CC
pin,
either during power up or live insertion, it starts in an under
voltage lockout (UVLO) state, ignoring any activity on the
SDA or SCL pins until V
CC
rises above 2.5V (typical).
During this time, the precharge circuitry is active and
forces 1V through 200k nominal resistors to the SDA
and SCL pins. Because the I/O card is being plugged
into a live backplane, the voltage on the backplane SDA
and SCL busses may be anywhere between 0V and V
CC
.
Precharging the SCL and SDA pins to 1V minimizes the
worst-case voltage differential these pins will see at the
moment of connection, therefore minimizing the amount
of disturbance caused by the I/O card.
Once the LTC4303 comes out of UVLO, it assumes that
SDAIN and SCLIN have been inserted into a live system
and that SDAOUT and SCLOUT are being powered up at
the same time as itself. Therefore, it looks for either a stop
bit or bus idle condition on the input side to indicate the
completion of a data transaction. When either one occurs,
the part also veri es that both the SDAOUT and SCLOUT
voltages are high. When all of these conditions are met,
the input-to-output connection circuitry is activated, join-
ing the SDA and SCL busses on the I/O card with those
on the backplane and READY goes high.
Connection Circuitry
Once the connection circuitry is activated, the functionality
of the SDAIN and SDAOUT pins is identical. A low forced
on either pin at any time results in both pin voltages be-
ing low. For proper operation, logic low input voltages
should be no higher than 0.4V with respect to the ground
pin voltage of the LTC4303. SDAIN and SDAOUT enter
a logic high state only when all devices on both SDAIN
and SDAOUT release high. The same is true for SCLIN
and SCLOUT. This important feature ensures that clock
stretching, clock synchronization, arbitration and the ac-
knowledge protocol always work, regardless of how the
devices in the system are tied to the LTC4303.
Another key feature of the connection circuitry is that it
provides bidirectional buffering, keeping the backplane
and card capacitances isolated. Because of this isolation,
OPERATIO
the waveforms on the backplane busses look slightly
different than the corresponding card bus waveforms, as
described here.
Input to Output Offset Voltage
When a logic low voltage, V
LOW1
, is driven on any of the
LTC4303s data or clock pins, the LTC4303 regulates the
voltage on the opposite side of the part (call it V
LOW2
)
to a slightly higher voltage, as directed by the following
equation:
V
LOW2
= V
LOW1
+ 75mV + (V
CC
/R) " 20?(typical)
where R is the bus pull-up resistance in ohms. For ex-
ample, if a device is forcing SDAOUT to 10mV where
V
CC
= 3.3V and the pull-up resistor R on SDAIN is 10k,
then the voltage on SDAIN = 10mV + 75mV + (3.3/10000)
" 20 = 91.6mV (typical). See the Typical Performance
Characteristics section for curves showing the offset
voltage as a function of V
CC
and R.
Bus Stuck Low Time-Out
When SDAOUT or SCLOUT is low, an internal timer starts.
The timer is only reset when SDAOUT and SCLOUT are
both high. If they do not go high within 30ms (typical),
the connection between SDAIN and SDAOUT, and SCLIN
and SCLOUT is broken. After a delay of at least 40祍 the
LTC4303 automatically generates up to 16 clock pulses at
8.5kHz (typical) on SCLOUT in an attempt to unstick the
bus. When SDAOUT and SCLOUT go high, reconnection
occurs when the conditions described in the Start-Up
section above are satis ed.
When powering up into a bus stuck low condition, the
connection circuitry joining the SDA and SCL busses on
the I/O card with those on the backplane is not activated.
30ms after UVLO, automatic clocking takes place as
described above.
Propagation Delays
During a rising edge, the rise-time on each side is de-
termined by the bus pull-up resistor and the equivalent
capacitance on the line. If the pull-up resistors are the
same, a difference in rise-time occurs which is directly
proportional to the difference in capacitance between
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4304IDD#TRPBF | IC BUS BUFFER I2C 10-DFN |
| LTC4307IMS8-1#TRPBF | IC BUFFER 2-WIRE BUS 8-MSOP |
| LTC4307IMS8#TRPBF | IC BUS BUFFER I2C 8-MSOP |
| LTC4308IMS8#TRPBF | IC BUS BUFFER LV 8-MSOP |
| LTC4309IGN#TRPBF | IC BUS BUFFER 2-WIRE 16-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4303CMS8 | 制造商:Linear Technology 功能描述:Hot Swappable Bus Buffer 8-Pin MSOP |
| LTC4303CMS8#PBF | 功能描述:IC BUS BUFFER I2C 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4303CMS8#PBF | 制造商:Linear Technology 功能描述:IC HOT SWAP BUS BUFFER MSOP-8 |
| LTC4303CMS8#TRPBF | 功能描述:IC BUS BUFFER I2C 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4303IDD#PBF | 功能描述:IC BUS BUFFER I2C 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。