參數資料
型號： LTC4263IS#TRPBF
廠商： Linear Technology
文件頁數： 19/24頁
文件大?。?/td> 354K
描述： IC IEEE 803.2AF CNTRLR 14-SOIC
標準包裝： 2,500
類型： 以太網供電（PoE）
應用： 用于以太網供電（PoE）設備的電源接口開關
電源電壓： 48V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 14-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 14-SOIC
包裝： 帶卷 (TR)
LTC4263
19
4263fe
APPLICATIONS INFORMATION
Fuse
While the LTC4263 does not require a fuse for proper
operation or for compliance with IEEE 802.3af, some
safety requirements state that the output current must be
limited to less than 2A in less than 60 seconds if any one
component fails or is shorted. Since the LTC4263 is the
primary current limiter, its failure could result in excess
current to the port. To meet these safety requirements, a
fuse can be placed in the positive leg of the port. The fuse
must be large enough that it will pass at least 450mA when
derated for high temperature but small enough that it will
fuse at less than 2A at cold temperature. This requirement
can usually be satis ed with a 1A fuse or PTC. Placing the
fuse between the RJ-45 connector and the LTC4263 and
its associated circuitry provides additional protection for
this circuitry. Consult a safety requirements expert for the
application speci c requirements.
Power Supply
Poor regulation on the 48V supply can lead to
noncompliance. The IEEE speci cation requires a PSE
output voltage between 44V and 57V. When the LTC4263
begins powering an Ethernet port, it controls the current
through the port to minimize disturbances on V
SS
. However,
if the V
SS
 supply is underdamped or otherwise unstable,
its voltage could go outside of the IEEE-speci ed limits,
causing the PSE to be noncompliant. This scenario can be
even worse when a PD is unplugged because the current
can drop immediately to zero. In both cases the port voltage
must always stay between 44V and 57V. Beyond this, the
IEEE 802.3af speci cation places speci c ripple, noise and
load regulation requirements on the PSE. Disturbances
on V
SS
 can also adversely affect detection, classi cation
and AC disconnect sensing. For these reasons, proper
bypassing and stability of the V
SS
 supply is important.
Another problem that can affect the V
SS
  supply is
insuf cient power, leading to the supply voltage dropping
out of the speci ed range. The 802.3af speci cation states
that if a PSE powers a PD it must be able to provide the
maximum power level requested by the PD based on
the PDs classi cation. The speci cation does allow a
PSE to choose not to power a port, typically because the
PD requires more power than the PSE has available to
deliver. If a PSE is built with a V
SS
 supply not capable of
delivering full power to all ports, it is recommended to
use the LTC4263 power management feature to prevent
ports from being turned on when there is insuf cient
power. Because the speci cation also requires the PSE
to supply an inrush current of 400mA at up to a 5% duty
cycle, the V
SS
 supply capability should be at least a few
percent higher than the maximum total power the PSE
needs to supply to the PDs.
Isolation
The IEEE 802.3af standard requires Ethernet ports to be
electrically isolated from all other conductors that are
user accessible. This includes the metal chassis, other
connectors, and the AC power line. Environment A isolation
is the most common and applies to wiring within a single
building serviced by a single AC power system. For this
type of application, the PSE isolation requirement can be
met with the use of a single, isolated 48V supply powering
several LTC4263 ports. Environment B, the stricter isolation
requirement, is for networks that cross an AC power
distribution boundary. In this case, electrical isolation
must be maintained between each port in the PSE. The
LTC4263 can be used to build a multi-port Environment B
PSE by powering each LTC4263 from a separate, isolated
48V supply. In all PSE applications, there should be no
user accessible connections to the LTC4263 other than
the RJ-45 port.
相關PDF資料
PDF描述
LTC4268IDKD-1#PBF IC PD HIGH POWER W/CNTRL 32-DFN
LTC4274CUHF#PBF IC CONTROLLER POE 38-QFN
LTC4280CUFD#PBF IC CONTROLLER HOT SWAP QFN-24
LTC4300-1IMS8#TRPBF IC HOTSWAP 2WIRE BUS BUFFR 8MSOP
LTC4300A-2IMS8#TRPBF IC BUFFER BUS 2WR HOTSWAP 8-MSOP
相關代理商/技術參數
參數描述
LTC4264 制造商:LINER 制造商全稱:Linear Technology 功能描述:Synchronous No-Opto Flyback Controller
LTC4264CDE 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Power PD Interface Controller with 750mA Current Limit
LTC4264CDE#PBF 功能描述:IC CNTRLR PD INTERFACE 12-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4264CDE#TRPBF 功能描述:IC INTERFACE 802.3AT 12-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4264IDE 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Power PD Interface Controller with 750mA Current Limit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*