參數資料
型號： LTC4261IGN-2#PBF
廠商： Linear Technology
文件頁數： 12/34頁
文件大?。?/td> 361K
描述： IC CTRLR HOTSWAP W/ADC 28-SSOP
標準包裝： 49
類型： 熱交換控制器
應用： 通用
內部開關： 無
電源電壓： 9 V ~ 11.2 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 28-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 28-SSOP
包裝： 管件
LTC4261/LTC4261-2
12
42612fc
The LTC4261/LTC4261-2 are designed to turn a boards
supply voltage on and off in a controlled manner, allowing
the board to be safely inserted or removed from a live  48V
backplane. The devices also feature an onboard 10-bit ADC
and I
2
C interface that allows monitoring board current,
voltages and faults. The main functional circuits of the
LTC4261/LTC4261-2 are illustrated in the Block Diagram.
In normal operation after a start-up debounce delay, the
GATE pin turns on the external N-channel FET passing
power to the load. The GATE pin is powered by a shunt
regulated 11.2V supply on the V
IN
 pin that is derived
from 48V RTN through a dropping resistor. The turn-on
sequence starts by pulling the SS pin up. The voltage at
the SS pin is converted to a current, I
GATE(UP)
, pulling the
GATE up. When the pass FET starts to turn on and charge
the load capacitor, the inrush current flowing through the
FET is a function of the capacitor at RAMP (C
R
), the load
capacitor (C
L
) and the ramp current (I
RAMP
) that flows
from the RAMP pin to C
R
:
 
I
INRUSH
=I
RAMP
C
L
C
R
I
RAMP
  and I
GATE(UP)
  are approximately proportional to
the SS pin voltage and are limited to 20礎 and 11.5礎,
respectively when SS reaches its clamping voltage (2.56V).
The ACL amplifier is used for overcurrent and short-circuit
protection. It monitors the load current through the SENSE
pin voltage and a sense resistor R
S
. In an overcurrent
condition, the ACL amplifier limits the current to 50mV/
R
S
 by pulling down GATE in an active servo loop. After a
530祍 timeout, the ACL amplifier turns off the pass FET .
In the event of a catastrophic short circuit, when V
SENSE
 
crosses 250mV , a fast response comparator immediately
pulls the GATE pin down.
The DRAIN and the GATE voltages are monitored to de-
termine if power is available for the load. Two power good
signals are sequenced on the PG pin (first power good
signal) and the PGIO pin (second power good signal), each
with a debounce delay that is twice the start-up delay. The
PGIO pin can also be used as a general purpose input or
output. The PGI pin serves as a watchdog to monitor the
output of the DC/DC module. If the module output fails to
come up, the LTC4261/LTC4261-2 shut down.
The TMR pin generates delays for initial start-up, auto-
retry following a fault, power good outputs and PGI check.
The logic circuits a re powered by an internally generated
5V supply (available on the INTV
CC
 pin). Prior to turning
on the pass FET , both V
IN
 and INTV
CC
 voltages must ex-
ceed their undervoltage lockout thresholds. In addition,
the control inputs UVH, UVL, OV , EN, ON and PGI are
monitored by comparators. The FET is held off until all
start-up conditions are met.
A 10-bit analog-to-digital converter (ADC) is included in the
LTC4261/LTC4261-2. The ADC measures SENSE resistor
voltage as well as voltage at the ADIN2/OV (SSOP/QFN)
and ADIN pins. The results are stored in on-board registers.
An I
2
C interface is provided to read the ADC data registers.
It also allows the host to poll the device and determine if a
fault has occurred. If the ALERT line is used as an interrupt,
the host can respond to a fault in real time. The SDA line
is divided into SDAI (input) and SDAO (output) to facili-
tate opto coupling with the system host. Two three-state
pins, ADR0 and ADR1, are used to decode eight device
addresses. The interface can also be configured through
the ADR0 and ADR1 pins for a single-wire broadcast
mode, sending ADC data and faults status through the
SDAO pin to the host without clocking the SCL line. This
single-wire, one-way communication simplifies system
design by eliminating two optocouplers on SCL and SDAI
that are required by an I
2
C interface.
OPERATION
相關PDF資料
PDF描述
LTC4263IS#TRPBF IC IEEE 803.2AF CNTRLR 14-SOIC
LTC4268IDKD-1#PBF IC PD HIGH POWER W/CNTRL 32-DFN
LTC4274CUHF#PBF IC CONTROLLER POE 38-QFN
LTC4280CUFD#PBF IC CONTROLLER HOT SWAP QFN-24
LTC4300-1IMS8#TRPBF IC HOTSWAP 2WIRE BUS BUFFR 8MSOP
相關代理商/技術參數
參數描述
LTC4261IUFD 功能描述:IC CTRLR HOTSWAP W/ADC 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4261IUFD#PBF 功能描述:IC CTRLR HOTSWAP W/ADC 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4261IUFD#TR 功能描述:IC CTRLR HOTSWAP W/ADC 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4261IUFD#TRPBF 功能描述:IC CTRLR HOTSWAP W/ADC 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4261IUFD-2 制造商:LINER 制造商全稱:Linear Technology 功能描述:Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*