參數資料
型號： LTC4240IGN#TRPBF
廠商： Linear Technology
文件頁數： 24/28頁
文件大?。?/td> 493K
描述： IC CTRLR HOTSWAP CPCI I2C 28SSOP
標準包裝： 2,500
類型： 熱交換控制器
應用： CompactPCI?
內部開關： 無
電源電壓： 3.3V，5V，±12V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 28-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 28-SSOP
包裝： 帶卷 (TR)
LTC4240
24
4240f
PRSNT1#
PRSNT2#
Expansion Configuration
Open
Open
No plug in board present
Ground
10k Pull-Up
Plug-in board present,
maximum power consumption
10k Pull-Up
Ground
Plug-in board present,
nominal power consumption
Ground
Ground
Plug-in board present,
minimum power consumption
Other CompactPCI Applications
If no 3.3V supply input is required, Figure 15 illustrates
how the LTC4240 should be configured.
For applications where the BD_SEL# connector pin is
grounded on the backplane, the circuit in Figure 16 allows
the LTC4240 to be reset simply by pressing a pushbutton
switch on the CPCI plug-in board. This arrangement
allows for manual resetting of the LTC4240s circuit break-
ers.
Input Transient Protection
Hot-plugging a board into a backplane generates inrush
currents from the backplane power supplies. This is due to
the charging of the plug-in board bulk capacitance. To
reduce this transient current to a safe level, the CPCI Hot
Swap specification restricts the amount of unswitched
capacitance used on the input side of the plug-in board.
Each pin connected to the CPCI female connector on the
plug-in board is allowed at most 0.01礔/pin. Bulk capaci-
tors are only allowed on the switched output side of the
LTC4240 (5V
OUT
, 3V
OUT
, 12V
OUT
, V
EEOUT
). Some bulk
capacitance is allowed on the Early Power planes, but only
because a current limiting resistor is assumed to separate
the connector from the bulk capacitor. Circuits normally
placed on the unswitched Early Power (PCI Bridge, for
example) need to have a current limiting resistor.
APPLICATIO  S I FOR  ATIO
U
U
U
The assumption by the CompactPCI specification is that
there is a diode to 3.3V on the circuit that is driving the
BD_SEL# pin. The 1.2k resistor pull up to 5V
IN
 on the plug-
in card will thus be clamped by the diode to 3.3V. If the
BD_SEL# pin is being driven high, the actual voltage on the
pin will be approximately 3.9V. This is still above the high
TTL threshold of the LTC4240 OFF/ON pin, but low enough
for Q4 to disable the bus switches and thus remove the 10k
resistors from the I/O lines. Note that BD_SEL# is ordi-
narily connected to V(I/O), which in turn is allowed to be
driven by either 3.3V or 5V. For applications such as
shown in Figure 14, the pull up on BD_SEL# is restricted
to the long 5V pins. A bus switch with no internal diode to
V
DD
 is preferred. Since the power to the bus switch is
derived from one of the unswitched power planes, a 100&
resistor plus a 0.1礔 bypass capacitor should be placed in
series with its power supply.
When the plug-in card is removed from the connector, the
BD_SEL# connection is broken first, and the BD_SEL#
voltage pulls up to 5V. This causes Q4 to turn off, which re-
enables the bus switch, and the precharge resistors are
again connected to the LTC4240 PRECHARGE pin for the
remainder of the board extraction process.
The LTC4240 BE pin can alternatively be used to drive the
enable input of the bus switch. The BE signal would then
keep the I/O lines precharged until all supplies reached
power good status. The resistor in series with the
PRECHARGE pin protects the internal circuitry from large
voltage transients during live insertion.
PRSNT1#, PRSNT2#
PRSNT1# and PRSNT2# are PCI signals that convey the
plug-in boards power consumption information. These
pins should either be shorted to ground or be connected
to Early Power with a 10k resistor. The voltage levels (TTL)
at the PRSNT#1, 2 pins can be read using the I
2
C 2-wire
interface.
相關PDF資料
PDF描述
LTC4241IGN#PBF IC CTRLR HOTSWAP 3.3V AUX 20SSOP
LTC4242CUHF#TRPBF IC CNTRLR HOT SWAP 38-QFN
LTC4244CGN-1#TRPBF IC CTRLR HOTSWAP PCI 20-SSOP
LTC4245CG#TRPBF IC CNTRLR HOT SWAP 36-SSOP
LTC4251-2CS6#TRPBF IC CTRLR HOTSWAP NEGVOLT SOT23-6
相關代理商/技術參數
參數描述
LTC4241 制造商:LINER 制造商全稱:Linear Technology 功能描述:PCI-Bus with 3.3V Auxiliary Hot Swap Controller
LTC4241CGN 功能描述:IC CTRLR HOTSWAP PCI 3.3V 20SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4241CGN#PBF 功能描述:IC CTRLR HOTSWAP CPCI I2C 20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4241CGN#TR 功能描述:IC CTRLR HOTSWAP 3.3V AUX 20SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4241CGN#TRPBF 功能描述:IC PCI-BUS W/HOT SWAP 20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*