- 您現在的位置：買賣IC網 > Datasheet目錄41 > LTC3446IDE#PBF (Linear Technology)IC REG TRPL BCK/LINEAR 14-DFN Datasheet資料下載
參數資料
| 型號： | LTC3446IDE#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 13/20頁 |
| 文件大?。?/td> | 283K |
| 描述： | IC REG TRPL BCK/LINEAR 14-DFN |
| 標準包裝： | 91 |
| 拓撲： | 降壓（降壓）同步（1），線性（LDO）（2） |
| 功能： | 任何功能 |
| 輸出數： | 3 |
| 頻率 - 開關： | 2.25MHz |
| 電壓/電流 - 輸出 1： | 可調至0.8V，1A |
| 電壓/電流 - 輸出 2： | 可調至0.4V，300mA |
| 電壓/電流 - 輸出 3： | 可調至0.4V，300mA |
| 帶 LED 驅動器： | 無 |
| 帶監控器： | 無 |
| 帶序列發生器： | 無 |
| 電源電壓： | 0.9 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 14-DFN-EP（4x3） |
| 包裝： | 管件 |
LTC3446
13
3446ff
applicaTions inForMaTion
Output Capacitor (C
OUTB
) Selection
The selection of C
OUTB
is driven by the required ESR to
minimize voltage ripple and load step transients. Typically,
once the ESR requirement is satisfied, the capacitance
is adequate for filtering. The output ripple (V
OUTB
) is
determined by:
V
OUTB
HI
L
ESR+
1
8f
O
C
OUTB
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
where f = 2.25MHz, C
OUTB
= output capacitance and
I
L
= ripple current in the inductor. The output ripple is
highest at maximum input voltage since I
L
increases
with input voltage.
Once the ESR requirements for C
OUTB
have been met, the
RMS current rating generally far exceeds the I
RIPPLE(P-P)
requirement, except for an all ceramic solution.
In surface mount applications, multiple capacitors may
have to be paralleled to meet the capacitance, ESR or RMS
current handling requirement of the application. Aluminum
electrolytic, special polymer, ceramic and dry tantulum
capacitors are all available in surface mount packages. The
OS-CON semiconductor dielectric capacitor available from
Sanyo has the lowest ESR(size) product of any aluminum
electrolytic at a somewhat higher price. Special polymer
capacitors, such as Sanyo POSCAP, offer very low ESR,
but have a lower capacitance density than other types.
Tantalum capacitors have the highest capacitance density,
but have a larger ESR and it is critical that the capacitors
are surge tested for use in switching power supplies.
An excellent choice is the AVX TPS series of surface
mount tantalums, avalable in case heights ranging from
2mm to 4mm. Aluminum electrolytic capacitors have a
significantly larger ESR, and are often used in extremely
cost-sensitive applications provided that consideration is
given to ripple current ratings and long-term reliability.
Ceramic capacitors have the lowest ESR and cost but also
have the lowest capacitance density, a high voltage and
temperature coefficient and exhibit audible piezoelectric
effects. In addition, the high Q of ceramic capacitors along
with trace inductance can lead to significant ringing. Other
capacitor types include the Panasonic specialty polymer
(SP) capacitors.
In most cases, 0.1礔 to 1礔 of ceramic capacitors should
also be placed close to the LTC3446 in parallel with the
main capacitors for high frequency decoupling.
Ceramic Input and Output Capacitors
Higher value, lower cost ceramic capacitors are now be-
coming available in smaller case sizes. These are tempting
for switching regulator use because of their very low ESR.
Unfortunately, the ESR is so low that it can cause loop
stability problems. Solid tantalum capacitor ESR gener-
ates a loop zero at 5kHz to 50kHz that is instrumental in
giving acceptable loop phase margin. Ceramic capacitors
remain capacitive to beyond 300kHz and usually resonate
with their ESL before ESR becomes effective. Also, ceramic
caps are prone to temperature effects which requires the
designer to check loop stability over the operating tem-
perature range. To minimize their large temperature and
voltage coefficients, only X5R or X7R ceramic capacitors
should be used. A good selection of ceramic capacitors
is available from Taiyo Yuden, TDK and Murata.
Great care must be taken when using only ceramic input
and output capacitors. When a ceramic capacitor is used
at the input and the power is being supplied through long
wires, such as from a wall adapter, a load step at the output
can induce ringing at the V
IN
pin. At best, this ringing can
couple to the output and be mistaken as loop instability.
At worst, the ringing at the input can be large enough to
damage the part.
Since the ESR of a ceramic capacitor is so low, the input
and output capacitor must instead fulfill a charge storage
requirement. During a load step, the output capacitor must
instantaneously supply the current to support the load
until the feedback loop raises the switch current enough
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3537EUD#TRPBF | IC REG DL BST/LINEAR SYNC 16-QFN |
| LTC3541EDD#TRPBF | IC REG DL BCK/LINEAR SYNC 10-DFN |
| LTC3670EDDB#TRPBF | IC REG TRPL BCK/LINEAR 12DFN |
| LTC3672BEDC-1#TRPBF | IC REG TRPL BCK/LINEAR 8-DFN |
| LTC3700EMS#TRPBF | IC REG DL BUCK/LINEAR 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3446IDE-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Monolithic Buck Regulator with Dual VLDO Regulators |
| LTC3447 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:I2C Controllable Buck Regulator in 3mm × 3mm DFN |
| LTC3447EDD | 功能描述:IC REG BUCK SYNC ADJ 0.6A 10DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC3447EDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LTC3447EDD#TR | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 2.5V to 5.5V 10-Pin DFN EP T/R |
發布緊急采購，3分鐘左右您將得到回復。