- 您現在的位置：買賣IC網 > PDF目錄10689 > LTC2488IDE#PBF (Linear Technology)IC ADC 16BIT DELTA SIG 14-DFN PDF資料下載
參數資料
| 型號： | LTC2488IDE#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 14/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT DELTA SIG 14-DFN |
| 標準包裝： | 91 |
| 位數： | 16 |
| 采樣率（每秒）： | 6.9 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 800µW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 14-DFN-EP（4x3） |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，雙極；2 個差分，雙極 |
| 產品目錄頁面： | 1348 (CN2011-ZH PDF) |
| 配用： | DC1009A-B-ND - BOARD DELTA SIGMA ADC LTC2488 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
LTC2488
21
2488fa
APPLICATIONS INFORMATION
Whenever SCK is LOW, the LTC2488’s internal pull-up at
SCK is disabled. Normally, SCK is not externally driven if
the device is operating in the internal SCK timing mode.
However, certain applications may require an external
driver on SCK. If the driver goes Hi-Z after outputting a
LOW signal, the internal pull-up is disabled. An external
10k pull-up resistor prevents the device from exiting the
internal SCK mode under this condition.
A similar situation may occur during the sleep state when
CS is pulsed HIGH-LOW-HIGH in order to test the conver-
sion status. If the device is in the sleep state (EOC = 0),
SCK will go LOW. If CS goes HIGH before the time tEOCtest,
the internal pull-up is activated. If SCK is heavily loaded,
the internal pull-up may not restore SCK to a HIGH state
before the next falling edge of CS. The external 10k pull-up
resistor prevents the device from exiting the internal SCK
mode under this condition.
PRESERVING THE CONVERTER ACCURACY
The LTC2488 is designed to reduce as much as possible
sensitivity to device decoupling, PCB layout, anti-aliasing
circuits, line frequency perturbations, and temperature
sensitivity. In order to achieve maximum performance a
few simple precautions should be observed.
Digital Signal Levels
The LTC2488’s digital interface is easy to use. Its digital
inputs SDI, FO, CS, and SCK (in external serial clock mode)
accept standard CMOS logic levels. Internal hysteresis
circuits can tolerate edge transition times as slow as
100μs.
The digital input signal range is 0.5V to VCC – 0.5V. During
transitions, the CMOS input circuits draw dynamic cur-
rent. For optimal performance, application of signals to
the serial data interface should be reserved for the sleep
and data output periods.
During the conversion period, overshoot and undershoot
of fast digital signals applied to both the serial digital in-
terface and the external oscillator pin (FO) may degrade
the converter performance. Undershoot and overshoot
occur due to impedance mismatch of the circuit board
trace at the converter pin when the transition time of an
external control signal is less than twice the propagation
delay from the driver to the input pin. For reference, on a
regular FR-4 board, the propagation delay is approximately
183ps/inch. In order to prevent overshoot, a driver with
a 1ns transition time must be connected to the converter
through a trace shorter than 2.5 inches. This becomes
difcult when shared control lines are used and multiple
reections occur.
Parallel termination near the input pin of the LTC2488 will
eliminate this problem, but will increase the driver power
dissipation. A series resistor from 27Ω to 54Ω (depend-
ing on the trace impedance and connection) placed near
the driver will also eliminate over/under shoot without
additional driver power dissipation.
For many applications, the serial interface pins (SCK, SDI,
CS, FO) remain static during the conversion cycle and
no degradation occurs. On the other hand, if an external
oscillator is used (FO driven externally) it is active during
the conversion cycle. Moreover, the digital lter rejection
is minimal at the clock rate applied to FO. Care must be
taken to ensure external inputs and reference lines do not
cross this signal or run near it. These issues are avoided
when using the internal oscillator.
Driving the Input and Reference
The input and reference pins of the LTC2488 are connected
directly to a switched capacitor network. Depending on
the relationship between the differential input voltage and
the differential reference voltage, these capacitors are
switched between these four pins. Each time a capacitor
is switched between two of these pins, a small amount
of charge is transferred. A simplied equivalent circuit is
shown in Figure 10.
When using the LTC2488’s internal oscillator, the input
capacitor array is switched at 123kHz. The effect of the
charge transfer depends on the circuitry driving the in-
put/reference pins. If the total external RC time constant
is less than 580ns the errors introduced by the sampling
process are negligible since complete settling occurs.
Typically, the reference inputs are driven from a low imped-
ance source. In this case, complete settling occurs even
with large external bypass capacitors. The inputs (CH0 to
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1443CN#PBF | IC COMP W/REF LOWPWR QUAD 16-DIP |
| LTC1443CN | IC COMP W/REF LOWPWR QUAD 16-DIP |
| LTC2489IDE#PBF | IC ADC 16BIT DELTA SIG 14-DFN |
| LT1017CSW#PBF | IC COMPARATOR MCRPWR DUAL 16SOIC |
| ISL31483EIBZ-T7A | IC TXRX RS485 FAULT PROT 14SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2489CDE#PBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2489CDE#TRPBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2489IDE | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 7.5sps 16-bit Serial 14-Pin DFN EP |
| LTC2489IDE#PBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2489IDE#TRPBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。