- 您現在的位置：買賣IC網 > Datasheet目錄41 > LT3570IFE#TRPBF (Linear Technology)IC REG BUCK/BST/LINEAR 20TSSOP Datasheet資料下載
參數資料
| 型號： | LT3570IFE#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 288K |
| 描述： | IC REG BUCK/BST/LINEAR 20TSSOP |
| 標準包裝： | 2,500 |
| 拓?fù)洌?/td> | 降壓（降壓）（1），升壓（升壓）（1），線性（LDO）（1） |
| 功能： | 車載 |
| 輸出數： | 3 |
| 頻率 - 開關： | 500kHz ~ 2.1MHz |
| 電壓/電流 - 輸出 1： | 可調至0.8V，1.5A |
| 電壓/電流 - 輸出 2： | 可調至0.8V，1.5A |
| 電壓/電流 - 輸出 3： | 控制器 |
| 帶 LED 驅動器： | 無 |
| 帶監控器： | 無 |
| 帶序列發生器： | 無 |
| 電源電壓： | 2.5 V ~ 36 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬）裸露焊盤 |
| 供應商設備封裝： | 20-TSSOP-EP |
| 包裝： | 帶卷 (TR) |
LT3570
11
3570fb
to 1.2A at DC2 = 0.8. The maximum output current is a
function of the chosen inductor value:
I
OUT2(MAX)
=I
LIM2
擨
L2
2
=1.5" 10.25"DC2
(
)
擨
L2
2
Choosing an inductor value so that the ripple current is
small will allow a maximum output current near the switch
current limit.
One approach to choosing the inductor is to start with the
simple rule given above, look at the available inductors
and choose one to meet cost or space goals. Then use
these equations to check that the LT3570 will be able to
deliver the required output current. Note again that these
equations assume that the inductor current is continu-
ous. Discontinuous operation occurs when I
OUT2
is less
than 擨
L2
/2.
Boost Inductor Selection
For most applications the inductor will fall in the range
of 2.2糎 to 22糎. Lower values are chosen to reduce
physical size of the inductor. Higher values allow more
output current because they reduce peak current seen by
the power switch, which has a 1.5A current limit. Higher
values also reduce input ripple voltage and reduce core
loss. The following procedure is suggested as a way of
choosing a more optimum inductor.
Assume that the average inductor current for a boost
converter is equal to the load current times V
OUT1
/V
IN1
and decide whether or not the inductor must withstand
continuous overload conditions. If average inductor cur-
rent at maximum load current is 0.5A, for instance, a 0.5A
inductor may not survive a continuous 1.5A overload
condition. Also be aware that boost converters are not
short-circuit protected, and that under short conditions,
inductor current is limited only by the available current
of the input supply.
Calculate peak inductor current at full load current to en-
sure that the inductor will not saturate. Peak current can
be signi cantly higher than output current, especially with
smaller inductors and lighter loads, so dont omit this step.
Powdered iron cores are forgiving because they saturate
softly, whereas ferrite cores saturate abruptly. Other
core materials fall somewhere in between. The following
formula assumes continuous mode operation but it errs
only slightly on the high side for discontinuous mode, so
it can be used for all conditions.
I
PEAK1
=
I
OUT1
"V
OUT1
V
IN1
+
V
IN1
V
OUT1
V
IN1
(
)
2"f"L"V
OUT1
Make sure that I
PEAK1
is less than the switch current I
LIM1
.
I
LIM1
is at least 1.5A at low duty cycles and decreases
linearly to 1.2A at DC1 = 0.8. The maximum switch current
limit can be calculated by the following formula:
I
LIM1
= 1.5 " (1 0.25 " DC1)
where DC1 is the duty cycle and is de ned as:
DC1=1
V
IN1
V
OUT1
Remember also that inductance can drop signi cantly with
DC current and manufacturing tolerance. Consideration
should also be given to the DC resistance of the inductor
as this contributes directly to the ef ciency losses in the
overall converter. Table 1 lists several inductor vendors
and types that are suitable.
Buck Output Capacitor Selection
For 5V and 3.3V outputs, a 10糉, 6.3V ceramic capacitor
(X5R or X7R) at the output results in very low output volt-
age ripple and good transient response. For lower voltages,
10糉 is adequate for ripple requirements but increasing
C
OUT
will improve transient performance. Other types and
values will also work; the following discusses tradeoffs in
output ripple and transient performance.
The output capacitor lters the inductor current to gener ate
an output with low voltage ripple. It also stores energy in
order to satisfy transient loads and stabilize the LT3570s
control loop. Because the LT3570 operates at a high
frequency, minimal output capacitance is necessary. In
addition, the control loop operates well with or without
the presence of output capacitor series resistance (ESR).
Ceramic capacitors, which achieve very low output ripple
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| LT3645HMSE#TRPBF | IC REG DL BUCK/LINEAR 12-MSOP |
| LT3694IFE-1#TRPBF | IC REG TRPL BUCK/LINEAR 20TSSOP |
| LT4220IGN#TR | IC CTLR HOTSWAP DUAL 16-SSOP |
| LT4250LCN8 | IC CONTRLR HOT SWAP NEG 48V 8DIP |
| LT4254CGN | IC CTRLR HOTSWAP POSVOLT 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3570IUF#PBF | 功能描述:IC REG TRPL BCK/BST/LINEAR 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3570IUF#TRPBF | 功能描述:IC REG TRPL BCK/BST/LINEAR 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3570IUF-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller |
| LT3570IUF-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller |
| LT3571EUD#PBF | 功能描述:IC REG BOOST ADJ 0.47A 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。