參數資料
型號： LT3570IFE#TRPBF
廠商： Linear Technology
文件頁數： 10/20頁
文件大?。?/td> 288K
描述： IC REG BUCK/BST/LINEAR 20TSSOP
標準包裝： 2,500
拓?fù)洌?/td> 降壓（降壓）（1），升壓（升壓）（1），線性（LDO）（1）
功能： 車載
輸出數： 3
頻率 - 開關： 500kHz ~ 2.1MHz
電壓/電流 - 輸出 1： 可調至0.8V，1.5A
電壓/電流 - 輸出 2： 可調至0.8V，1.5A
電壓/電流 - 輸出 3： 控制器
帶 LED 驅動器： 無
帶監控器： 無
帶序列發生器： 無
電源電壓： 2.5 V ~ 36 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 20-TSSOP（0.173"，4.40mm 寬）裸露焊盤
供應商設備封裝： 20-TSSOP-EP
包裝： 帶卷 (TR)
LT3570
10
3570fb
APPLICATIONS INFORMATION
FB Resistor Network 
The output voltage is programmed with a resistor divider
(refer to the Block Diagram) between the output and the
FB pin. Choose the resistors according to:
 
 
R1=R2
V
OUT
788mV
1
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
Buck Inductor Selection and Maximum Output Current
A good  rst choice for the inductor value is
   
L=
V
OUT2
+V
F
0.75"f
 for SW2
where V
F
 is the voltage drop of the catch diode (~0.4V)
and f is the switching frequency. With this inductance
value or greater, the maximum load current will be 1A,
independent of input voltage. The inductors RMS current
rating must be greater than the maximum load current and
its saturation current should be at least 30% higher. For
highest ef ciency, the series resistance (DCR) should be
less than 0.1? Table 1 lists several vendors and types
that are suitable.
Table 1. Inductors
PART NUMBER
VALUE
(糎)
I
SAT
(A)
DCR
(?/SPAN>)
HEIGHT
(mm)
Sumida
CDRH4D28-3R3
3.3    1.57   0.049    3.0
CDRH4D28-4R7
4.7    1.32   0.072    3.0
CDC5D23-2R2
2.2    2.50    0.03    2.5
CR43-3R3
3.3    1.44   0.086    3.5
CDRH5D28-100
10    1.3    0.048    3.0
Coilcraft
DO1608C-332
3.3    2.00   0.080    2.9
DO1608C-472
4.7    1.50   0.090    2.9
MOS6020-332
3.3    1.8    0.046    2.0
D03314-103
10    0.8    0.520    1.4
D03314-222
2.2    1.6    0.200    1.4
Toko
(D62F)847FY-2R4M
2.4    2.5    0.037    2.7
(D73LF)817FY-2R2M
2.2    2.7    0.03    3.0
Coiltronics
TP3-4R7
4.7    1.5    0.181    2.2
TP1-2R2
2.2    1.3    0.188    1.8
TP4-100
10    1.5    0.146    3.0
The optimum inductor for a given application may differ
from the one indicated by this simple design guide. A
larger value inductor provides a slightly higher maximum
load current and will reduce the output voltage ripple. If
your load is lower than the maximum load current, then
you can relax the value of the inductor and operate with
higher ripple current. This allows you to use a physically
smaller inductor or one with a lower DCR resulting in
higher ef ciency. Be aware that if the inductance differs
from the simple rule above, then the maximum load current
will depend on input voltage. In addition, low inductance
may result in discontinuous mode operation, which further
reduces maximum load current. For details of maximum
output current and discontinuous mode operation, see
Linear Technologys Application Note 44. Finally, for duty
cycles greater than 50% (V
OUT2
/V
IN2
 > 0.5) a minimum
inductance is required to avoid subharmonic oscillations,
see Application Note 19.
The current in the inductor is a triangle wave with an average
value equal to the load current. The peak switch current
is equal to the output current plus half the peak-to-peak
inductor ripple current. The LT3570 limits its switch cur-
rent in order to protect itself and the system from overload
faults. Therefore, the maximum output current that the
LT3570 will deliver depends on the switch current limit,
the inductor value and the input and output voltages.
When the switch is off, the potential across the inductor
is the output voltage plus the catch diode drop. This gives
the peak-to-peak ripple current in the inductor:
   
擨
L2
=
1DC2
(
)
V
OUT2
+V
F
(
)
L"f
where DC2 is the duty cycle and is de ned as:
 
 
DC2=
V
OUT2
V
IN2
The peak inductor and switch current is:
   
I
SWPK2
=I
LPK2
=I
OUT2
+
擨
L2
2
To maintain output regulation, this peak current must be
less than the LT3570s switch current limit I
LIM2
. I
LIM2
 is
at least 1.5A at low duty cycles and decreases linearly
相關PDF資料
PDF描述
LT3645HMSE#TRPBF IC REG DL BUCK/LINEAR 12-MSOP
LT3694IFE-1#TRPBF IC REG TRPL BUCK/LINEAR 20TSSOP
LT4220IGN#TR IC CTLR HOTSWAP DUAL 16-SSOP
LT4250LCN8 IC CONTRLR HOT SWAP NEG 48V 8DIP
LT4254CGN IC CTRLR HOTSWAP POSVOLT 16SSOP
相關代理商/技術參數
參數描述
LT3570IUF#PBF 功能描述:IC REG TRPL BCK/BST/LINEAR 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:*
LT3570IUF#TRPBF 功能描述:IC REG TRPL BCK/BST/LINEAR 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:*
LT3570IUF-PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller
LT3570IUF-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller
LT3571EUD#PBF 功能描述:IC REG BOOST ADJ 0.47A 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*