- 您現在的位置：買賣IC網 > Datasheet目錄41 > LT1939IDD#TRPBF (Linear Technology)IC REG DL BUCK/LINEAR 12DFN Datasheet資料下載
參數資料
| 型號： | LT1939IDD#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 19/24頁 |
| 文件大?。?/td> | 349K |
| 描述： | IC REG DL BUCK/LINEAR 12DFN |
| 標準包裝： | 2,500 |
| 拓撲： | 降壓（降壓）（1），線性（LDO）（1） |
| 功能： | 任何功能 |
| 輸出數： | 2 |
| 頻率 - 開關： | 500kHz ~ 2.4MHz |
| 電壓/電流 - 輸出 1： | 0.8 V ~ 24.25 V，2A |
| 電壓/電流 - 輸出 2： | 0.8 V ~ 24.25 V，1A |
| 帶 LED 驅動器： | 無 |
| 帶監控器： | 無 |
| 帶序列發生器： | 無 |
| 電源電壓： | 3 V ~ 25 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 12-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 12-DFN |
| 包裝： | 帶卷 (TR) |
LT1939
19
1939f
When the SS pin voltage is below 100mV, the V
C
pin is
pulled low which disables switching. As the SS pin voltage
rises above 100mV, the V
C
pin is released and the outputs
are regulated to the SS voltage. When the SS pin voltage
minus 100mV exceeds the internal 0.8V reference, the
outputs are regulated to the reference. The SS pin voltage
will continue to rise until it is clamped at 2V.
In the event of a V
IN
undervoltage lockout, the SHDN pin
driven below 0.8V, or the internal die temperature exceeding
its maximum rating during normal operation, the soft-start
latch is set, triggering a start-up sequence.
In addition, if the load exceeds the maximum output switch
current (switching regulator only), the output will start to
drop causing the V
C
pin clamp to be activated. As long as
the V
C
pin is clamped, the SS pin will be discharged. As
a result, the output will be regulated to the highest volt-
age that the maximum output current can support. For
example, if a 6V output is loaded by 1?the SS pin will
drop to 0.5V, regulating the output at 3V (typical current
limit time load, 3A " 1?. Once the overload condition is
removed, the output will soft-start from the temporary
voltage level to the normal regulation point.
Since the SS pin is clamped at 2V and has to discharge to
0.9V before taking control of regulation, momentary over-
load conditions will be tolerated without a soft-start recov-
ery. The typical time before the SS pin takes control is:
t
SS(CONTROL)
=
C
SS
"1.1V
600?/DIV>
A
Power Good Indicators
The PG and PG pins are collector outputs of an internal
comparator. The comparator compares the voltages of
the FB and LFB pins to 90% of the reference voltage with
30mV of hysterisis.
The PG pin has a sink capability of 400糀 when the FB and
LFB pins are below the threshold and can withstand 25V
when the outputs are in regulation. The PG pin is typically
connected to the output with a resistor and is used as an
error ag. The resistor value should be chosen to allow the
PG voltage to drop below 0.4V in an error condition.
Example:
V
OUT1
= 5V, PGSINK
(MIN)
= 200糀
R
PG
= (5 0.4)/200糀 = 23k?/DIV>
The PG pin has a sink capability of 800糀 when the FB
and LFB pins are above the threshold and can withstand
25V when the outputs are not in regulation. The PG pin is
typically used as a drive signal for an output disconnect
device. The PG pull-up resistor should be sized in the
same manner as the PG pull-up resistor.
Linear Regulator
The LT1939 contains an error ampli er and a NPN output
device which can be con gured as a linear regulator or as
a linear regulator controller.
With the LFB and LDRV pins con gured as shown in
Figure 1, the LDRV pin outputs a regulated voltage with a
typical current limit of 13mA.
The LDRV voltage is programmed with a resistor divider
between the output and the LFB pin. Choose the 1% resis-
tors according to:
R3=R4
V
LDRV
0.8
V
1
R4 should be 10.0k or less to avoid bias current errors.
Reference designators refer to the Block Diagram in
Figure 1.
The reference voltage for the linear regulator (LFB pin)
will track the SS pin in the same manner as the FB pin of
the switching regulator.
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| LT3092MPST#TRPBF | IC PROG CURRENT SOURCE SOT223-3 |
| LT3150CGN#TRPBF | IC REG CTRLR SGL POS ADJ 16-SSOP |
| LT3500HMSE#TRPBF | IC REG DL BUCK/LINEAR 16-MSOP |
| LT3507HUHF#TRPBF | IC REG QD BUCK/LINEAR 38-QFN |
| LT3570IFE#TRPBF | IC REG BUCK/BST/LINEAR 20TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1940 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Synchronous,400mA/800mA, 2.25MHz Step-Down DC/DC Regulator |
| LT1940EFE | 功能描述:IC REG BUCK ADJ 1.4A DL 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1940EFE#PBF | 功能描述:IC REG BUCK ADJ 1.4A DL 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT1940EFE#TR | 功能描述:IC REG BUCK ADJ 1.4A DL 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1940EFE#TRPBF | 功能描述:IC REG BUCK ADJ 1.4A DL 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
發布緊急采購，3分鐘左右您將得到回復。