參數資料
型號： LT1939IDD#TRPBF
廠商： Linear Technology
文件頁數： 16/24頁
文件大?。?/td> 349K
描述： IC REG DL BUCK/LINEAR 12DFN
標準包裝： 2,500
拓?fù)洌?/td> 降壓（降壓）（1），線性（LDO）（1）
功能： 任何功能
輸出數： 2
頻率 - 開關： 500kHz ~ 2.4MHz
電壓/電流 - 輸出 1： 0.8 V ~ 24.25 V，2A
電壓/電流 - 輸出 2： 0.8 V ~ 24.25 V，1A
帶 LED 驅動器： 無
帶監控器： 無
帶序列發生器： 無
電源電壓： 3 V ~ 25 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 12-WFDFN 裸露焊盤
供應商設備封裝： 12-DFN
包裝： 帶卷 (TR)
LT1939
16
1939f
Generally, for outputs of 3.3V and higher the standard
circuit (Figure 5a) is the best. For outputs between 2.8V
and 3.3V, replace the D2 with a small Schottky diode such
as the PMEG4005.
For lower output voltages the boost diode can be tied to
the input (Figure 5b). The circuit in Figure 5a is more ef-
 cient because the BST pin current comes from a lower
voltage source.
Figure 5c shows the boost voltage source from the linear
output that is set to greater than 2.5V (any available DC
sources that are greater than 2.5V is suf cient). The highest
ef ciency is attained by choosing the lowest boost volt-
age above 2.5V. You must also be sure that the maximum
voltage at the BST pin is less than the maximum speci ed
in the Absolute Maximum Ratings section.
The boost circuit can also run directly from a DC voltage
that is higher than the input voltage by more than 2.5V, as
in Figure 5d. The diode is used to prevent damage to the
LT1939 in case V
X
 is held low while V
IN
 is present. The
circuit eliminates a capacitor, but ef ciency may be lower
and dissipation in the LT1939 may be higher. Also, if V
X
 is
absent, the LT1939 will still attempt to regulate the output,
but will do so with very low ef ciency and high dissipation
because the switch will not be able to saturate, dropping
1.5V to 2V in conduction.
The minimum input voltage of an LT1939 application is
limited by the minimum operating voltage (<2.8V) and by
the maximum duty cycle as outlined above. For proper
start-up, the minimum input voltage is also limited by
the boost circuit. If the input voltage is ramped slowly, or
the LT1939 is turned on with its SS pin when the output
is already in regulation, then the boost capacitor may not
be fully charged. Because the boost capacitor is charged
with the energy stored in the inductor, the circuit will rely
on some minimum load current to get the boost circuit
running properly. This minimum load will depend on
input and output voltages and on the arrangement of the
boost circuit.
The Typical Performance Characteristics section shows
plots of the minimum load current to start and to run as a
function of input voltage for 3.3V and 5V outputs. In many
cases the discharged output capacitor will present a load
to the switcher which will allow it to start. The plots show
the worst-case situation where V
IN
 is ramping very slowly.
Use a Schottky diode for the lowest start-up voltage.
Frequency Compensation
The LT1939 uses current mode control to regulate the
output. This simpli es loop compensation. In particular, the
LT1939 does not require the ESR of the output capacitor
for stability so you are free to use ceramic capacitors to
achieve low output ripple and small circuit size. Frequency
compensation is provided by the components tied to the
V
C
 pin. Generally a capacitor and a resistor in series to
ground determine loop gain. In addition, there is a lower
value capacitor in parallel. This capacitor is not part of
the loop compensation but is used to  lter noise at the
switching frequency.
Loop compensation determines the stability and transient
performance. Designing the compensation network is a bit
complicated and the best values depend on the application
and in particular the type of output capacitor. A practical
approach is to start with one of the circuits in this data
sheet that is similar to your application and tune the com-
pensation network to optimize the performance. Stability
should then be checked across all operating conditions,
including load current, input voltage and temperature.
The LT1375 data sheet contains a more thorough discus-
sion of loop compensation and describes how to test the
stability using a transient load.
Figure 6 shows an equivalent circuit for the LT1939 control
loop. The error amp is a transconductance ampli er with
 nite output impedance. The power section, consisting of
the modulator, power switch, and inductor, is modeled as
a transconductance ampli er generating an output cur-
rent proportional to the voltage at the V
C
 pin. Note that
the output capacitor integrates this current, and that the
capacitor on the V
C
 pin (C
C
) integrates the error ampli-
 er output current, resulting in two poles in the loop. In
most cases a zero is required and comes from either the
output capacitor ESR or from a resistor in series with C
C
.
This simple model works well as long as the value of the
inductor is not too high and the loop crossover frequency
APPLICATIONS INFORMATION
相關PDF資料
PDF描述
LT3092MPST#TRPBF IC PROG CURRENT SOURCE SOT223-3
LT3150CGN#TRPBF IC REG CTRLR SGL POS ADJ 16-SSOP
LT3500HMSE#TRPBF IC REG DL BUCK/LINEAR 16-MSOP
LT3507HUHF#TRPBF IC REG QD BUCK/LINEAR 38-QFN
LT3570IFE#TRPBF IC REG BUCK/BST/LINEAR 20TSSOP
相關代理商/技術參數
參數描述
LT1940 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Synchronous,400mA/800mA, 2.25MHz Step-Down DC/DC Regulator
LT1940EFE 功能描述:IC REG BUCK ADJ 1.4A DL 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LT1940EFE#PBF 功能描述:IC REG BUCK ADJ 1.4A DL 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2
LT1940EFE#TR 功能描述:IC REG BUCK ADJ 1.4A DL 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LT1940EFE#TRPBF 功能描述:IC REG BUCK ADJ 1.4A DL 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*