- 您現在的位置：買賣IC網 > PDF目錄3861 > LPC3250FET296,551 (NXP Semiconductors)IC ARM9 MCU 256K 296-TFBGA PDF資料下載
參數資料
| 型號： | LPC3250FET296,551 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 12/57頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ARM9 MCU 256K 296-TFBGA |
| 特色產品： | LPC32x0 ARM926EJ-S Processor |
| 標準包裝： | 126 |
| 系列： | LPC3200 |
| 核心處理器： | ARM9 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 266MHz |
| 連通性： | EBI/EMI，以太網，I²C，IrDA，Microwire，SPI，SSI，SSP，UART/USART，USB OTG |
| 外圍設備： | DMA，I²S，LCD，電機控制 PWM，PWM，WDT |
| 輸入/輸出數： | 51 |
| 程序存儲器類型： | ROMless |
| RAM 容量： | 256K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 0.9 V ~ 3.6 V |
| 數據轉換器： | A/D 3x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 296-TFBGA |
| 包裝： | 托盤 |
| 配用： | 568-4743-ND - KIT LCD TOUCH 5.7" FOR LPC3250 568-4742-ND - MODULE DIMM LPC2478 ARM7 622-1030-ND - KIT LCD TOUCH 5.7" FOR LPC3250 |
| 其它名稱： | 568-4533 935287084551 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
LPC3220_30_40_50
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 20 October 2011
2 of 79
NXP Semiconductors
LPC3220/30/40/50
16/32-bit ARM microcontrollers
External memory controller for DDR and SDR SDRAM as well as for static devices.
Two NAND flash controllers: One for single-level NAND flash devices and the other for
multi-level NAND flash devices.
Master Interrupt Controller (MIC) and two Slave Interrupt Controllers (SIC), supporting
74 interrupt sources.
Eight channel General Purpose DMA (GPDMA) controller on the AHB that can be
used with the SD card port, the high-speed UARTs, I2S-bus interfaces, and SPI
interfaces, as well as memory-to-memory transfers.
Serial interfaces:
10/100 Ethernet MAC with dedicated DMA Controller.
USB interface supporting either device, host (OHCI compliant), or On-The-Go
(OTG) with an integral DMA controller and dedicated PLL to generate the required
48 MHz USB clock.
Four standard UARTs with fractional baud rate generation and 64 byte FIFOs. One
of the standard UARTs supports IrDA.
Three additional high-speed UARTs intended for on-board communications that
support baud rates up to 921 600 when using a 13 MHz main oscillator. All
high-speed UARTs provide 64 byte FIFOs.
Two SPI controllers.
Two SSP controllers.
Two I2C-bus interfaces with standard open-drain pins. The I2C-bus interfaces
support single master, slave, and multi-master I2C-bus configurations.
Two I2S-bus interfaces, each with separate input and output channels. Each
channel can be operated independently on three pins, or both input and output
channels can be used with only four pins and a shared clock.
Additional peripherals:
LCD controller supporting both STN and TFT panels, with dedicated DMA
controller. Programmable display resolution up to 1024
768.
Secure Digital (SD) memory card interface, which conforms to the SD Memory
Card Specification Version 1.01.
General Purpose (GP) input, output, and I/O pins. Includes 12 GP input pins, 24
GP output pins, and 51 GP I/O pins.
10-bit, 400 kHz Analog-to-Digital Converter (ADC) with input multiplexing from
three pins. Optionally, the ADC can operate as a touch screen controller.
Real-Time Clock (RTC) with separate power pin and dedicated 32 kHz oscillator.
NXP implemented the RTC in an independent on-chip power domain so it can
remain active while the rest of the chip is not powered. The RTC also includes a
32-byte scratch pad memory.
32-bit general purpose high-speed timer with a 16-bit pre-scaler. This timer
includes one external capture input pin and a capture connection to the RTC clock.
Interrupts may be generated using three match registers.
Six enhanced timer/counters which are architecturally identical except for the
peripheral base address. Two capture inputs and two match outputs are pinned out
to four timers. Timer 1 brings out a third match output, timers 2 and 3 bring out all
four match outputs, timer 4 has one match output, and timer 5 has no inputs or
outputs.
32-bit millisecond timer driven from the RTC clock. This timer can generate
interrupts using two match registers.
相關PDF資料 |
PDF描述 |
|---|---|
| P89V51RB2FA,529 | IC 80C51 MCU FLASH 16K 44-PLCC |
| P89V660FA,512 | IC 80C51 MCU FLASH 16K 44-PLCC |
| P89V660FBC,557 | IC 80C51 MCU FLASH 16K 44-TQFP |
| P89V662FBC,557 | IC 80C51 MCU FLASH 32K 44-TQFP |
| PIC32MX130F064B-I/SO | IC MCU 32BIT 64KB FLASH 28-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC-35 | 功能描述:LED電源 RoHS:否 制造商:Cree, Inc. 工作模式:Constant Voltage (CV) 輸出功率額定值: 輸入電壓:220 V to 240 V 輸出端數量:1 輸出電壓（通道 1）:40 V 輸出電流（通道 1）:900 mA 安裝風格:Screw 尺寸:90 mm L x 90 mm W x 37.5 mm H 商用/醫用:Commercial |
| LPC-35_11 | 制造商:MEANWELL 制造商全稱:Mean Well Enterprises Co., Ltd. 功能描述:35W Single Output Switching Power Supply |
| LPC-35_12 | 制造商:MEANWELL 制造商全稱:Mean Well Enterprises Co., Ltd. 功能描述:35W Single Output Switching Power Supply |
| LPC-35-1050 | 功能描述:LED電源 31.5W 30V 1050mA RoHS:否 制造商:Cree, Inc. 工作模式:Constant Voltage (CV) 輸出功率額定值: 輸入電壓:220 V to 240 V 輸出端數量:1 輸出電壓（通道 1）:40 V 輸出電流（通道 1）:900 mA 安裝風格:Screw 尺寸:90 mm L x 90 mm W x 37.5 mm H 商用/醫用:Commercial |
| LPC-35-1400 | 功能描述:LED電源 33.6W 24V 1400mA RoHS:否 制造商:Cree, Inc. 工作模式:Constant Voltage (CV) 輸出功率額定值: 輸入電壓:220 V to 240 V 輸出端數量:1 輸出電壓（通道 1）:40 V 輸出電流（通道 1）:900 mA 安裝風格:Screw 尺寸:90 mm L x 90 mm W x 37.5 mm H 商用/醫用:Commercial |
發布緊急采購，3分鐘左右您將得到回復。