參數資料
型號： LPC2212
廠商： NXP Semiconductors N.V.
英文描述： 16/32-bit ARM microcontrollers; 128/256 kB ISP/IAP Flash with 10-bit ADC and external memory interface
中文描述： 16/32位ARM微控制器; 128/256 kB ISP / IAP閃存的10位模數轉換器和外部存儲器接口
文件頁數： 14/40頁
文件大?。?/td> 185K
代理商： LPC2212
Philips Semiconductors
LPC2212/LPC2214
16/32-bit ARM microcontrollers with external memory interface
Product data
Rev. 02 — 23 December 2004
14 of 40
9397 750 13149
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Vectored IRQs have the middle priority. Sixteen of the interrupt requests can be
assigned to this category. Any of the interrupt requests can be assigned to any of the
16 vectored IRQ slots, among which slot 0 has the highest priority and slot 15 has the
lowest.
Non-vectored IRQs have the lowest priority.
The VIC combines the requests from all the vectored and non-vectored IRQs to
produce the IRQ signal to the ARM processor. The IRQ service routine can start by
reading a register from the VIC and jumping there. If any of the vectored IRQs are
requesting, the VIC provides the address of the highest-priority requesting IRQs
service routine, otherwise it provides the address of a default routine that is shared by
all the non-vectored IRQs. The default routine can read another VIC register to see
what IRQs are active.
6.5.1
Interrupt sources
Table 4
lists the interrupt sources for each peripheral function. Each peripheral device
has one interrupt line connected to the Vectored Interrupt Controller, but may have
several internal interrupt flags. Individual interrupt flags may also represent more than
one interrupt source.
Table 4:
Block
WDT
-
ARM Core
ARM Core
Timer0
Timer1
UART0
Interrupt sources
Flag(s)
Watchdog Interrupt (WDINT)
Reserved for software interrupts only
Embedded ICE, DbgCommRx
Embedded ICE, DbgCommTx
Match 0 - 3 (MR0, MR1, MR2, MR3)
Match 0 - 3 (MR0, MR1, MR2, MR3)
Rx Line Status (RLS)
Transmit Holding Register empty (THRE)
Rx Data Available (RDA)
Character Time-out Indicator (CTI)
Rx Line Status (RLS)
Transmit Holding Register empty (THRE)
Rx Data Available (RDA)
Character Time-out Indicator (CTI)
Modem Status Interrupt (MSI)
Match 0 - 6 (MR0, MR1, MR2, MR3, MR4, MR5, MR6)
SI (state change)
SPIF, MODF
SPIF, MODF
PLL Lock (PLOCK)
RTCCIF (Counter Increment), RTCALF (Alarm)
VIC channel #
0
1
2
3
4
5
6
UART1
7
PWM0
I
2
C
SPI0
SPI1
PLL
RTC
8
9
10
11
12
13
相關PDF資料
PDF描述
LPC2214 16/32-bit ARM microcontrollers; 128/256 kB ISP/IAP Flash with 10-bit ADC and external memory interface
LPC2220 16/32-bit ARM microcontrollers; flashless with 64 kB, with 10-bit ADC and external memory interface
LPC2364FB100 Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2364 Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2366 Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
相關代理商/技術參數
參數描述
LPC2212_08 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:16/32-bit ARM microcontrollers; 128/256 kB ISP/IAP flash with 10-bit ADC and external memory interface
LPC2212_11 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16/32-bit ARM microcontrollers; 128/256 kB ISP/IAP flash with 10-bit ADC
LPC2212FBD101 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16/32-bit ARM microcontrollers; 128/256 kB ISP/IAP flash with 10-bit ADC
LPC2212FBD144 制造商:NXP Semiconductors 功能描述:16/32BIT MCU ARM7 128K FLASH 144LQFP 制造商:NXP Semiconductors 功能描述:16/32BIT MCU ARM7, 128K FLASH, 144LQFP
LPC2212FBD144,551 功能描述:ARM微控制器 - MCU PREF PART LPC2212FBD144/01-S RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*