- 您現在的位置：買賣IC網 > PDF目錄361044 > LMX9820SB (National Semiconductor Corporation) Bluetooth Serial Port Module PDF資料下載
參數資料
| 型號： | LMX9820SB |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Bluetooth Serial Port Module |
| 中文描述： | 藍牙串行端口模塊 |
| 文件頁數： | 32/40頁 |
| 文件大?。?/td> | 567K |
| 代理商： | LMX9820SB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
www.national.com
32
L
14.0 Application Information
Figure 21 on page 32 represents a typical system sche-
matic for the LMX9820.
14.1 MATCHING NETWORK
The antenna matching network may or may not be
required, depending upon the impedance of the antenna
chosen. A 6.8pF blocking capacitor is recommended.
14.2 FILTERED POWER SUPPLY
It is imperative that the LMX9820 be provided with ade-
quate Ground planes and a filtered power supply. It is
highly recommended that a 0.1
μF and a 10 pF bypass
capacitor be placed as close as possible to VCC (pad H2)
on the LMX9820.
14.3 HOST INTERFACE
To set the logic thresholds of the LMX9820 to match the
host system, IOVCC (pad H12) must be connected to the
logic power supply of the host system. It is highly recom-
mended that a 10 pF bypass capacitor be placed as close
as possible to the IOVCC pad on the LMX9820.
ISEL2 (pad H13) and ISEL1 (pad J13) can be strapped to
the host logic 0 and 1 levels to set the host interface boot-
up configuration. Alternatively both ISEL2 and ISEL1 can
be hardwired over 10K
pull-up/pull-down resistors.
Env0 (pad E9) and Env1 (pad B11) can be left uncon-
nected (both are read as high) if no ISP capability is
required. If the environment mode ISP needs to be acti-
vated by hardware (alternatively a firmware upgrade com-
mand can be used) then Env0 must be set to Logical Low
and Reset needs to be set. Upon removal of Reset, the
LMX9820 boots into the mode corresponding to the values
present on Env0 and Env1.
14.4 CLOCK INPUT
The clock source must be placed as close as possible to
the LMX9820. The quality of the radio performance is
directly related to the quality of the clock source connected
to the oscillator port on the LMX9820. Careful attention
must be paid to the crystal/oscillator parameters or radio
performance could be drastically reduced.
14.5 SCHEMATIC AND LAYOUT EXAMPLES
Notes:
Capacitor values, C1, C2, C31 & C32, may vary depending on board design crystal manufacturer specification.
Single ground plane is used for both RF and Digital grounds.
Figure 21. Example System Schematic with pre-selected 115.2kbit/s UART speed
B1 Antenna
RF_inout
H8
Clk+
B9
Clk-
B8
12 MHz
Y1
10 pF
C1
10 pF
C2
VCC
10 pF
0.01 μF
H2
10 pF
0.01 μF
H12
IOVCC
Reset_b
Reset_5100
Env0
Env1
Uart_rx
Uart_tx
Uart_cts
Uart_rts
D11
G8
E9
B11
C8
D9
D10
C10
G12
RF GND
Dig_gnd[1:2]
LMX9820
USBGND
D12, G11
Reference
Table 19 on
page 15.
Reference
Table 18 on
page 15.
Reference
Table 24 on
page 20 for
correct POR
timing.
Connect
system
UART bus.
to
ISEL2
ISEL1
H13
J13
6.8 pF
相關PDF資料 |
PDF描述 |
|---|---|
| LMX9820SBX | Bluetooth Serial Port Module |
| LP3882ESX-1.2 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882ESX-1.5 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882ESX-1.8 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882 | 1.5A Fast-Response Ultra Low Dropout Linear |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMX9820SBX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Bluetooth Serial Port Module |
| LMX9830 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:BluetoothTM Serial Port Module |
| LMX9830DONGLE | 功能描述:藍牙/802.15.1 開發工具 LMX9830 BLUETOOTH EVAL KIT RoHS:否 制造商:Panasonic Electronic Components 產品:Bluetooth Evaluation Kit 工具用于評估:PAN1721 頻率:2.4 GHz 接口類型:I2C 工作電源電壓:2 V to 3.6 V |
| LMX9830DONGLE/NOPB | 制造商:Texas Instruments 功能描述:Evaluation Kit For Bluetooth Serial Port Module |
| LMX9830SM | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:BluetoothTM Serial Port Module |
發布緊急采購，3分鐘左右您將得到回復。