- 您現在的位置：買賣IC網 > PDF目錄361044 > LMX9820SB (National Semiconductor Corporation) Bluetooth Serial Port Module PDF資料下載
參數資料
| 型號： | LMX9820SB |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Bluetooth Serial Port Module |
| 中文描述： | 藍牙串行端口模塊 |
| 文件頁數： | 21/40頁 |
| 文件大?。?/td> | 567K |
| 代理商： | LMX9820SB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Revision 1.0
21
www.national.com
L
10.0 Integrated Firmware
The LMX9820 includes the full Bluetooth stack up to
RFComm to support the following profiles:
GAP (Generic Access Profile)
SDAP (Service Discovery Application Profile)
SPP (Serial Port Profile)
Figure 15 shows the Bluetooth protocol stack with com-
mand interpreter interface. The command interpreter offers
a number of different commands to support the functional-
ity given by the different profiles. Execution and interface
timing is handled by the control application.
The chip has an internal data area in Flash that includes
the parameters shown in Table 25 on page 22.
10.1 FEATURES
10.1.1 Operation Modes
On boot-up, the application configures the module follow-
ing the parameters in the data area.
Automatic Mode
No Default Connections Stored:
In Automatic mode the module is connectable and discov-
erable and automatically answers to service requests. The
command interpreter listens to commands and links can be
set up. The full command list is supported.
If connected by another device, the module sends an event
back to the host, where the RFComm port has been con-
nected, and switches to transparent mode.
Default Connections Stored:
If default connections were stored on a previous session,
once the LMX9820 is reset, it will attempt to connect each
device stored within the data Flash three times. The host
will be notified about the success of the link setup via a link
status event.
Command Mode
In Command mode, the LMX9820 does not check the
default connections section within the Data Flash. If con-
nected by another device, it will NOT switch to transparent
mode and continue to interpret data sent on the UART.
Transparent Mode
The LMX9820 supports transparent data communication
from the UART interface to a bluetooth link.
If activated, the module does not interpret the commands
on the UART which normally are used to configure and
control the module. The packages don’t need to be format-
ted as described in Table 27 on page 24. Instead all data
are directly passed through the firmware to the active blue-
tooth link and the remote device.
Transparent mode can only be supported on a point-to-
point connection. To leave Transparent mode, the host
must send a UART_BREAK signal to the module
Force Master Mode
In Force Master mode tries to act like an Accesspoint for
multiple connections. For this it will only accept the link if a
Master/slave role switch is accepted by the connecting
device. After successful link establishment the LMX9820
will be Master and available for additional incoming links.
On the first incoming link the LMX9820 will switch to trans-
parent depending on the setting for automatic or command
mode. Additional links will only be possible if the device is
not in transparent mode.
10.1.2 Default Connections
The LMX9820 supports the storage of up to 3 devices
within its NVS. Those connections can either be connected
after reset or on demand using a specific command.
10.1.3 Event Filter
The LMX9820 uses events or indicators to notify the host
about successful commands or changes at the bluetooth
interface. Depending on the application the LMX9820 can
be configured. The following levels are defined:
No Events:
– The LMX9820 is not reporting any events. Optimized
for passive cable replacement solutions.
Standard LMX9820 events:
– only necessary events will be reported
All events:
– Additional to the standard all changes at the physical
layer will be reported.
10.1.4 Default Link Policy
Each Bluetooth Link can be configured to support M/S role
switch, Hold Mode, Sniff Mode and Park Mode. The default
link policy defines the standard setting for incoming and
outgoing connections.
Figure 15. LMX9820 Software Implementation
Command Interpreter
Control Application
SPP
GAP
SDAP
RFComm
L2CAP
Link Manager
Baseband
SDP
相關PDF資料 |
PDF描述 |
|---|---|
| LMX9820SBX | Bluetooth Serial Port Module |
| LP3882ESX-1.2 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882ESX-1.5 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882ESX-1.8 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882 | 1.5A Fast-Response Ultra Low Dropout Linear |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMX9820SBX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Bluetooth Serial Port Module |
| LMX9830 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:BluetoothTM Serial Port Module |
| LMX9830DONGLE | 功能描述:藍牙/802.15.1 開發工具 LMX9830 BLUETOOTH EVAL KIT RoHS:否 制造商:Panasonic Electronic Components 產品:Bluetooth Evaluation Kit 工具用于評估:PAN1721 頻率:2.4 GHz 接口類型:I2C 工作電源電壓:2 V to 3.6 V |
| LMX9830DONGLE/NOPB | 制造商:Texas Instruments 功能描述:Evaluation Kit For Bluetooth Serial Port Module |
| LMX9830SM | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:BluetoothTM Serial Port Module |
發布緊急采購，3分鐘左右您將得到回復。