- 您現在的位置：買賣IC網 > PDF目錄358760 > LC72714 (Sanyo Electric Co.,Ltd.) Mobile FM Multiplex Broadcast IC with On-Chip VICS Decoder PDF資料下載
參數資料
| 型號： | LC72714 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Mobile FM Multiplex Broadcast IC with On-Chip VICS Decoder |
| 中文描述： | 多重移動調頻廣播集成電路片VICS解碼器 |
| 文件頁數： | 16/29頁 |
| 文件大?。?/td> | 232K |
| 代理商： | LC72714 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
No. 6871-16/29
LC72714W
V
DD
voltage
RST
2.5 V
V
IL
(0.3 V
DD
)
V
IH
300 ns (min)
Notes on Operation during Resets and in Standby Mode
Reset Signal
The reset operation is executed when the supply voltage (V
DD
) rises above 2.5 V (2.5 V in the LC72710LW) and the
RST pin input level is held at or below V
IL
for 300 ns or longer. (See the figure below.)
When power is first applied, or when power is removed and applied again, always apply a reset before using this IC.
Pin States during Reset
Low level:CLK16 (5), DATA (6), FLOCK (7), BLOCK (8), FCK (9), BCK (10)
High level: INT (33), RDY (16), CRC4 (11), DREQ (12)
Open: D0 (17) to D15 (32), DO (36)
Reset Operating Range
The states of the output pins as the result of a reset signal are stipulated in the "Pin States during Reset" item above. The
IC internal flip-flops are all reset. While the shift registers used for delay are also reset, the memory array is not
influenced by this operation. However, since memory is not refreshed, data cannot be retained. The crystal oscillator
circuit is not stopped.
Post-Reset Data Input
After a reset operation has completed, if at least one clock cycle (about 278 ns when the IC's main clock is 3.6 MHz)
elapses, the register write circuit will be functional. (That is, the IC can accept data.)
Notes on Standby Mode
The IC is set to standby mode by applying a high level to the STNBY pin. Since all IC operations are stopped in this
mode, the state is essentially equivalent to removing power from the IC. (Note that after clearing standby mode,
applications must wait the oscillator stabilization time before using the IC.)
The pin output states during standby mode are the same as those states during a reset as described above. The internal
VICS registers are cleared and the status flag values are not retained.
Output Conditions for Post-Error Correction Output (Default Mode)
(1) For each block (272 bits) of received data, the IC applies (272, 190) code error correction and a layer 2 CRC error
check. After the error correction has completed, the IC prepares to transfer the data to the CPU and outputs an
interrupt signal from the INT pin. This is referred to as horizontal correction output.
(2) Note that under the default operating conditions, this interrupt signal is not output unless the corresponding output
data meets the following three conditions.
Error correction completed correctly and no errors were discovered in the layer 2 CRC check.
The data was received in both block and frame synchronization.
The data is packet data.
(3) If the data could not be corrected in horizontal correction, product code correction is performed in frame units and
a second horizontal correction operation is performed for this data that could not be corrected by the first
horizontal correction. This sequence of operations is called vertical correction.
The output conditions for data that can be acquired after vertical correction are as follows.
The data that could not be corrected by horizontal correction only, but that was corrected by vertical correction.
The data is packet data.
Continued on next page.
相關PDF資料 |
PDF描述 |
|---|---|
| LC72714W | Mobile FM Multiplex Broadcast IC with On-Chip VICS Decoder |
| LC72720NM | Single-Chip RDS Signal-Processing System LSI(單片無線電數據系統信號處理LSI（大規模集成電路）) |
| LC72720YV | Single-Chip RDS Signal-Processing System IC(單片無線電數據系統信號處理芯片) |
| LC72720 | Single-Chip RDS Signal-Processing System LSI |
| LC72720M | Single-Chip RDS Signal-Processing System LSI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC72714W | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Mobile FM Multiplex Broadcast IC with On-Chip VICS Decoder |
| LC72715PW | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Mobile FM Multiplex Broadcast IC with On-Chip VICS Decoder |
| LC72717PW | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Mobile FM Multiplex Broadcast (DARC) Receiver IC |
| LC72720 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip RDS Signal-Processing System LSI |
| LC72720M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip RDS Signal-Processing System LSI |
發布緊急采購，3分鐘左右您將得到回復。