參數資料
型號: LAN91C96I
廠商: SMSC Corporation
英文描述: NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
中文描述: 非PCI單芯片以太網控制器全DUPLES
文件頁數: 82/110頁
文件大?。?/td> 655K
代理商: LAN91C96I
Non-PCI Single-Chip Full Duplex Ethernet Controller
Rev.
11/18/2004
Page 82
SMSC DS – LAN91C96I
DATASHEET
Chapter 10
Board Setup Information
The following parameters are obtained
from the EEPROM as board setup
information:
ETHERNET INDIVIDUAL ADDRESS
I/O BASE ADDRESS
ROM BASE ADDRESS
8/16 BIT ADAPTER
10BASE-T or AUI INTERFACE
INTERRUPT LINE SELECTION
REGISTER
EEPROM WORD
ADDRESS
IOS Value * 4
(IOS Value *4) + 1
Configuration Register
Base Register
All the above mentioned values are read from the EEPROM upon hardware reset. Except for the
INDIVIDUAL ADDRESS, the value of the IOS switches determines the offset within the EEPROM for these
parameters, in such a way that many identical boards can be plugged into the same system by just
changing the IOS jumpers.
In order to support a software utility based installation, even if the EEPROM was never programmed, the
EEPROM can be written using the LAN91C96I. One of the IOS combination is associated with a fixed
default value for the key parameters (I/O BASE, ROM BASE, INTERRUPT) that can always be used
regardless of the EEPROM based value being programmed. This value will be used if all IOS pins are left
open or pulled high.
The EEPROM is arranged as a 64 x 16 array. The specific target device is the 9346 1024-bit Serial
EEPROM. All EEPROM accesses are done in words. All EEPROM addresses shown are specified as
word addresses.
INDIVIDUAL ADDRESS 20-22 hexIf IOS2-0 = 7, only the INDIVIDUAL ADDRESS is read from the
EEPROM. Currently assigned values are assumed for the other registers. These values are default if the
EEPROM read operation follows hardware reset.
The EEPROM SELECT bit is used to determine the type of EEPROM operation: a) normal or b) general
purpose register.
a) NORMAL EEPROM OPERATION - EEPROM SELECT bit = 0
On EEPROM read operations (after reset or after setting RELOAD high) the CONFIGURATION
REGISTER and BASE REGISTER are updated with the EEPROM values at locations defined by the
IOS2-0 pins. The INDIVIDUAL ADDRESS registers are updated with the values stored in the
INDIVIDUAL ADDRESS area of the EEPROM.
On EEPROM write operations (after setting the STORE bit) the values of the CONFIGURATION
REGISTER and BASE REGISTER are written in the EEPROM locations defined by the IOS2-0 pins.
The three least significant bits of the CONTROL REGISTER (EEPROM SELECT, RELOAD and
STORE) are used to control the EEPROM. Their values are not stored nor loaded from the EEPROM.
b) GENERAL PURPOSE REGISTER - EEPROM SELECT bit = 1
相關PDF資料
PDF描述
LAN91C96I-MS NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
LAN91C96I-MU NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
LAN91C96IQFP NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
LAN91C96ITQFP NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
LANF72351D ETHERNET 10BASE-T LAN FILTER MODULES
相關代理商/技術參數
參數描述
LAN91C96I_07 制造商:SMSC 制造商全稱:SMSC 功能描述:Non-PCI Single-Chip Full Duplex Ethernet Controller
LAN91C96IMS 制造商:Microchip Technology Inc 功能描述:
LAN91C96I-MS 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96I-MU 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96IQFP 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray