- 您現在的位置：買賣IC網 > PDF目錄358742 > LAN91C110TQFP (STANDARD MICROSYSTEMS CORP) FEAST FAST ETHERNET CONTROLLER FOR PCMCIA AND GENERIC 16-BIT APPLICATIONS PDF資料下載
參數資料
| 型號： | LAN91C110TQFP |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | FEAST FAST ETHERNET CONTROLLER FOR PCMCIA AND GENERIC 16-BIT APPLICATIONS |
| 中文描述： | 4 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PQFP144 |
| 封裝： | TQFP-144 |
| 文件頁數： | 25/55頁 |
| 文件大?。?/td> | 482K |
| 代理商： | LAN91C110TQFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
FEAST Fast Ethernet Controller
for PCMCIA and Generic 16-Bit Applications
SMSC DS – LAN91C110 REV. B
Page 25
Rev. 09/05/02
BANK2
OFFSET
0
NAME
TYPE
SYMBOL
MMUCR
MMU COMMAND REGISTER
WRITE ONLY
BUSY Bit Readable
This register is used by the CPU to control the memory allocation, de-allocation, TX FIFO and RX FIFO control. The three
command bits determine the command issued as described below:
HIGH
BYTE
LOW
BYTE
COMMAND
Reserved
Reserved
N2
N1
N0/BUSY
X
Y
Z
0
COMMAND SET:
xyz
000
0)
NOOP - NO OPERATION
001
1)
ALLOCATE MEMORY FOR TX - N2, N1, N0 defines the amount of memory requested as (value + 1) * 256
bytes. Namely N2, N1, N0 = 1 will request 2 * 256 = 512 bytes. A shift-based divide by 256 of the packet
length yields the appropriate value to be used as N2, N1, N0. Immediately generates a completion code at
the ALLOCATION RESULT REGISTER. Can optionally generate an interrupt on successful completion. N2,
N1, N0 are ignored by the LAN91C110 but should be implemented in LAN91C110 software drivers for
LAN9000 compatibility.
010
2)
RESET MMU TO INITIAL STATE - Frees all memory allocations, clears relevant interrupts, resets packet
FIFO pointers.
011
3)
REMOVE FRAME FROM TOP OF RX FIFO - To be issued after CPU has completed processing of present
receive frame. This command removes the receive packet number from the RX FIFO and brings the next
receive frame (if any) to the RX area (output of RX FIFO).
100
4)
REMOVE AND RELEASE TOP OF RX FIFO - Like 3) but also releases all memory used by the packet
presently at the RX FIFO output. The MMU busy time after issuing REMOVE and RELEASE command
depends on the time when the busy bit is cleared. The time from issuing REMOVE and RELEASE command
on the last receive packet to the time when receive FIFO is empty depends on RX INT bit turning low. An
alternate approach can be checking the read RX FIFO register.
101
5)
RELEASE SPECIFIC PACKET - Frees all pages allocated to the packet specified in the PACKET NUMBER
REGISTER. Should not be used for frames pending transmission. Typically used to remove transmitted
frames, after reading their completion status. Can be used following 3) to release receive packet memory in
a more flexible way than 4).
110
6)
ENQUEUE PACKET NUMBER INTO TX FIFO - This is the normal method of transmitting a packet just
loaded into RAM. The packet number to be enqueued is taken from the PACKET NUMBER REGISTER.
111
7)
RESET TX FIFOs - This command will reset both TX FIFOs: The TX FIFO holding the packet numbers
awaiting transmission and the TX Completion FIFO. This command provides a mechanism for canceling
packet transmissions, and reordering or bypassing the transmit queue. The RESET TX FIFOs command
should only be used when the transmitter is disabled. Unlike the RESET MMU command, the RESET TX
FIFOs does not release any memory.
相關PDF資料 |
PDF描述 |
|---|---|
| LAN91C96I | NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER |
| LAN91C96I-MS | NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER |
| LAN91C96I-MU | NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER |
| LAN91C96IQFP | NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER |
| LAN91C96ITQFP | NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN91C110-TQFP | 制造商:SMSC 功能描述: |
| LAN91C111 | 制造商:SMSC 制造商全稱:SMSC 功能描述:10/100 Non-PCI Ethernet Single Chip MAC + PHY |
| LAN91C111I-NC | 功能描述:以太網 IC Non-PCI 10/100 Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN91C111INE | 制造商:SMSC 功能描述:NEW |
| LAN91C111I-NE | 功能描述:以太網 IC Non-PCI 10/100 Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。