參數資料
型號： L6706
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： SWITCHING REGULATOR, QCC40
封裝： 6 X 6 MM, ROHS COMPLIANT, VFQFPN-40
文件頁數： 25/47頁
文件大?。?/td> 623K
代理商： L6706
L6706
Soft-start
Doc ID 15698 Rev 2
31/47
14
Soft-start
L6706 implements a soft-start to smoothly charge the output filter avoiding high in-rush
currents to be required to the input power supply. The device increases the reference from
zero up to the programmed value and the output voltage increases accordingly with closed
loop regulation.
The device implements soft-start only when all the power supplies are above their own turn-
on thresholds and the OUTEN pin is set free.
At the end of the digital soft-start, SS_END signal is set free.
Protections are active during soft-start: Under voltage is enabled when the reference voltage
reaches 0.6 V while over voltage is always enabled.
Figure 13.
Soft-start
Once L6706 receives all the correct supplies and enables, it initiates the soft-start phase
with a TD1 = 1.5 ms (typ) delay. After that, the reference ramps up to VBOOT = 1.081 V (1.100
V - 19 mV) in TD2 according to the SSOSC settings and waits for TD3 = 200 μsec (typ) during
which the device reads the VID lines. Output voltage will then ramps up to the programmed
value in TD4 with the same slope as before (See Figure 13).
SSOSC defines the frequency of an internal additional soft-start-oscillator used to step the
reference from zero up to the programmed value; this oscillator is independent from the
main oscillator whose frequency is programmed through the OSC pin.
The current flowing from SSOSC pin before the end of soft-start is used to program the
desiderated soft-start time (TSS).
After that the soft-start is finished the current flowing from SSOSC pin is used to program
the maximum LTB switching frequency (FLIMIT).
In the Figure 14 is shown the SSOSC connection in order to select both parameter (TSS and
FLIMIT) in independent way.
In particular, it allows to precisely programming the startup time up to VBOOT (TD2) since it is
a fixed voltage independent by the programmed VID. Total soft-start time dependence on
the programmed VID results (see Figure 15).
Note:
If during TD3 the programmed VID selects an output voltage lower than VBOOT, the output
voltage will ramp to the programmed voltage starting from VBOOT.
OUTEN
SS_END
VOUT
t
T
D1
T
D2
T
D3TD4
TSS
OVP
T
D5
相關PDF資料
PDF描述
L6717 DUAL SWITCHING CONTROLLER, 575 kHz SWITCHING FREQ-MAX, QCC48
L6728HTR SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO10
L6728H SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO10
L6728 1.5 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, DSO10
L6728TR 1.5 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, DSO10
相關代理商/技術參數
參數描述
L6706TR 功能描述:DC/DC 開關控制器 VR11.1 SINGLE PHASE CNTRL W/INT DRI RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6709 功能描述:功率驅動器IC 6-Bit Dual Ph Contlr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L6709TR 功能描述:功率驅動器IC 6-Bit Dual Ph Contlr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L6710 功能描述:功率驅動器IC 6-Bit Dual Ph Contlr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L6710TR 功能描述:功率驅動器IC 6-Bit Dual Ph Contlr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*