參數資料
型號： KAC-1310
廠商： Electronic Theatre Controls, Inc.
英文描述： 1280 (H) x 1024 (V) SXGA CMOS Image Sensor
中文描述： 1280（高）x 1024（五）SXGA CMOS圖像傳感器
文件頁數： 57/76頁
文件大小： 759K
代理商： KAC-1310
IMAGE SENSOR SOLUTIONS
57
IMAGE SENSOR SOLUTIONS
K A C - 1 3 1 0 R e v 4 w w w . k o d a k . c o m / g o / i m a g e r s 5 8 5 - 7 2 2 - 4 3 8 5 E m a i l : i m a g e r s @ k o d a k . c o m
TRIGGER and STROBE Control Register (42
h
)
The
saw
bit allows the user to select how long the
STROBE signal is going to be on. If the bit is set
to 1, the STROBE output will go high when all
lines are concurrently integrating and will go low
when the integration time has completed and
readout has begun. It is during this period while
STROBE is high that a mechanical shutter must
open and close and/or flash must fire and quench
if these devices are being used with the imager. If
the shutter or flash operate at any other time
image artifacts can result. Note the integration
time must be greater than a frame readout time for
this output to be useful. The
sae
bit when enabled
will enable the STROBE signal to be generated
automatically by the sensor. This will only work in
Single Frame Rolling Shutter (SFRS) mode.
The
se
bit, when enabled, will allow for an external
signal to drive the trigger signal via the TRIGGER
pin on the chip. Enabling the
sa
bit forces the
trigger signal high until this bit is disabled. This
causes continuous frame processing in SFRS
mode. The
sr
bit, when enabled, causes the
TRIGGER signal to go high for exactly one clock
cycle, and then returns to a low. It remains low
until the
sr
bit is enabled again. This is used to
trigger a single frame capture via I
2
C rather than
the TRIGGER pin.
Address
42
h
TRIGGER and STROBE Control
Default
02
h
7 (msb)
6
5
4
3
2
1
0 (lsb)
x
x
sso
saw
sae
se
sa
sr
Bit
Number
Function
Description
Reset
State
7 - 6
Unused
Unused
xx
b
5
Factory Use Only
0
b
4
Strobe Width 0
b
= 1 line time
1
b
= Pulse width is high while all rows are simultaneously integrating
0
b
3
STROBE
Enable
0
b
= STROBE pin Disabled
1
b
= STROBE pin Enabled
0
b
2
TRIGGER
Enable
0
b
= External TRIGGER input pin Disabled (ignored)
1
b
= External TRIGGER input pin Enabled
0
b
1
TRIGGER
Always On
0
b
= No effect
1
b
= TRIGGER input is internally held HIGH, TRIGGER input pin is
ignored
1
b
0
Software
TRIGGER
0
b
= No effect
1
b
= Triggers a single frame capture via I
2
C
0
b
Table 29: TRIGGER and STROBE Control Register (42
h
)
相關PDF資料
PDF描述
KAF-1001E 1024(H) x 1024(V) Pixel Enhanced Response Full-Frame CCD Image Sensor Performance Specification
KAF-1602E Replacement for Texas Instruments part number SN74LS164N. Buy from authorized manufacturer Rochester Electronics.
KaLNA3S.04R Ka Band Low Noise Amplifier(工作頻率從33GHz到36GHz的低噪聲Ka波段功率放大器)
KAQW214 PHOTO MOS RELAYS
KAQW414A HIGH VOLTAGE, PHOTO MOS RELAY
相關代理商/技術參數
參數描述
KAC-15 功能描述:保險絲 600V 15A Semiconductor RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485
KAC-150 功能描述:保險絲 600V 150A Semiconductor RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485
KAC-17.5 制造商:COOPER 制造商全稱:Cooper Bussmann, Inc. 功能描述:High Speed Fuses
KAC-17-1/2 功能描述:保險絲 600V 17.5A Semiconductor RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485
KAC-17-1-2 制造商:Cooper Bussmann 功能描述:FUSE 17.5A 600V 2PIN - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*