參數資料
型號： ISP1362BD
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： Single-chip Universal Serial Bus On-The-Go controller
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, PQFP64
封裝： 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64
文件頁數： 58/150頁
文件大小： 647K
代理商： ISP1362BD
Philips Semiconductors
ISP1362
Single-chip USB OTG controller
Product data
Rev. 03
—
06 January 2004
58 of 150
9397 750 12337
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Isochronous endpoints:
A DMA transfer to or from an isochronous endpoint can be
terminated by any of the following conditions (bit names refer to the
DcDMACon
fi
guration register, see
Table 118
and
Table 119
):
The DMA transfer completes as programmed in the DcDMACounter register
(CNTREN = 1)
An End-Of-Packet (EOP) signal is detected
DMA operation is disabled by clearing bit DMAEN.
13.5 ISP1362 DC suspend and resume
13.5.1
Suspend conditions
The DC in the ISP1362 detects a USB suspend condition in either of the following
cases:
Constant idle state is present on the USB bus for 3 ms.
V
BUS
is lost.
Bus-powered devices that are suspended must not consume more than 500
μ
A of
current. This is achieved by shutting down the power to system components or
supplying them with a reduced voltage.
The steps leading the DC to the suspend state are as follows:
1. In the event of no SOF for 3 ms, the DC in the ISP1362 sets bit SUSPND of the
DcInterrupt register. This will generate an interrupt if bit IESUSP of the
DcInterruptEnable register is set.
2. When the
fi
rmware detects a suspend condition (through the IESUSP), it must
prepare all system components for the suspend state:
a. All the signals connected to the DC in the ISP1362 must enter appropriate
states to meet the power consumption requirements of the suspend state.
b. All the input pins of the DC in the ISP1362 must have a CMOS logic 0 or
logic 1 level.
3. In the interrupt service routine, the
fi
rmware must check the current status of the
USB bus. When bit BUSTATUS of the DcInterrupt register is logic 0, the USB bus
has left the suspend mode and the process must be aborted. Otherwise, the next
step can be executed.
4. To meet the suspend current requirements for a bus-powered device, the internal
clocks must be switched off by clearing bit CLKRUN of the
DcHardwareCon
fi
guration register.
5. When the
fi
rmware has set and cleared the GOSUSP bit of the DcMode register,
the DC in the ISP1362 enters the suspend state. It sets the
D_SUSPEND/D_WAKEUP pin to HIGH and switches off the internal clocks after
2 ms.
Table 20:
EOT condition
DcDMACounter register zero
Recommended EOT usage for isochronous endpoints
OUT endpoint
do not use
IN endpoint
preferred
相關PDF資料
PDF描述
ISP1362EE Single-chip Universal Serial Bus On-The-Go controller
ISP1501 Hi-Speed Universal Serial Bus peripheral transceiver
ISP1520 Hi-Speed Universal Serial Bus hub controller
ISP1520BD Hi-Speed Universal Serial Bus hub controller
ISP1521 Hi-Speed Universal Serial Bus hub controller
相關代理商/技術參數
參數描述
ISP1362BD,118 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,151 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD,157 功能描述:USB 接口集成電路 USB OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362BD157 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB-OTG 64LQFP 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB OTG 64-LQFP
ISP1362BDFA 功能描述:IC USB OTG CONTROLLER 64-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*