- 您現在的位置：買賣IC網 > PDF目錄383154 > ISL6530EVAL1 (Intersil Corporation) Dual Low-Noise High-Drive Operational Amplifier 8-PDIP 0 to 70 PDF資料下載
參數資料
| 型號： | ISL6530EVAL1 |
| 廠商： | Intersil Corporation |
| 英文描述： | Dual Low-Noise High-Drive Operational Amplifier 8-PDIP 0 to 70 |
| 中文描述： | 雙同步降壓5V的脈寬調制（PWM）控制器，用于數據存儲器內存VDDQ和VTT終端 |
| 文件頁數： | 13/17頁 |
| 文件大小： | 540K |
| 代理商： | ISL6530EVAL1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁
13
FN9052.2
November 15, 2004
Output Inductor Selection
The output inductor is selected to meet the output voltage
ripple requirements and minimize the converter’s response
time to the load transient. The inductor value determines the
converter’s ripple current and the ripple voltage is a function
of the ripple current. The ripple voltage and current are
approximated by the following equations:
Increasing the value of inductance reduces the ripple current
and voltage. However, the large inductance values reduce
the converter’s response time to a load transient.
One of the parameters limiting the converter’s response to
a load transient is the time required to change the inductor
current. Given a sufficiently fast control loop design, the
ISL6530 will provide either 0% or 100% duty cycle in
response to a load transient. The response time is the time
required to slew the inductor current from an initial current
value to the transient current level. During this interval the
difference between the inductor current and the transient
current level must be supplied by the output capacitor.
Minimizing the response time can minimize the output
capacitance required.
The response time to a transient is different for the
application of load and the removal of load. The following
equations give the approximate response time interval for
application and removal of a transient load:
where: I
TRAN
is the transient load current step, t
RISE
is the
response time to the application of load, and t
FALL
is the
response time to the removal of load. The worst case
response time can be either at the application or removal of
load. Be sure to check both of these equations at the
response time.
Input Capacitor Selection
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use small ceramic
capacitors for high frequency decoupling and bulk capacitors
to supply the current needed each time Q
1
turns on. Place the
small ceramic capacitors physically close to the MOSFETs
and between the drain of Q
1
and the source of Q
2
.
The important parameters for the bulk input capacitor are the
voltage rating and the RMS current rating. For reliable
operation, select the bulk capacitor with voltage and current
ratings above the maximum input voltage and largest RMS
current required by the circuit. The capacitor voltage rating
should be at least 1.25 times greater than the maximum
input voltage and a voltage rating of 1.5 times is a
conservative guideline. The RMS current rating requirement
for the input capacitor of a buck regulator is approximately
1/2 the DC load current.
The maximum RMS current required by the regulator may be
closely approximated through the following equation:
For a through-hole design, several electrolytic capacitors may
be needed. For surface mount designs, solid tantalum
capacitors can be used, but caution must be exercised with
regard to the capacitor surge currentrating. These capacitors
must be capable of handling the surge-current at power-up.
Some capacitor series available from reputable manufacturers
are surge current tested.
MOSFET Selection/Considerations
The ISL6530 requires two N-Channel power MOSFETs for
each PWM regulator. These should be selected based upon
r
DS(ON)
, gate supply requirements, and thermal management
requirements.
In high-current applications, the MOSFET power dissipation,
package selection and heatsink are the dominant design
factors. The power dissipation includes two loss components;
conduction loss and switching loss. The conduction losses are
the largest component of power dissipation for both the upper
and the lower MOSFETs. These losses are distributed between
the two MOSFETs according to duty factor. The switching
losses seen when sourcing current will be different from the
switching losses seen when sinking current. The V
DDQ
regulator will only source current while the V
TT
regulator can
sink and source. When sourcing current, the upper MOSFET
realizes most of the switching losses. The lower switch realizes
most of the switching losses when the converter is sinking
current (see the equations below). These equations assume
linear voltage-current transitions and do not adequately model
power loss due the reverse-recovery of the upper and lower
MOSFET’s body diode. The gate-charge losses are dissipated
by the ISL6530 and don't heat the MOSFETs. However, large
gate-charge increases the switching interval, t
SW
which
increases the
MOSFET
switching losses.
I
=
V
IN
- V
OUT
f
s
x L
V
OUT
V
IN
V
OUT
=
I
x
ESR
x
t
RISE
=
L x I
TRAN
V
IN
- V
OUT
t
FALL
=
L x I
TRAN
V
OUT
I
RMSMAX
V
V
IN
-------------
I
OUTMAX
2
1
12
------
V
-----------–
V
f
s
L
V
V
IN
-------------
×
2
×
+
×
=
P
LOWER
= Io
2
x r
DS(ON)
x (1 - D)
Where: D is the duty cycle = V
OUT
/ V
IN
,
t
SW
is the combined switch ON and OFF time, and
f
s
is the switching frequency.
LOSSES WHILE SOURCING CURRENT
Io
2
r
DS ON
LOSSES WHILE SINKING CURRENT
P
UPPER
= Io
2
x r
DS(ON)
x D
P
LOWER
Io
2
r
DS ON
)
×
1
D
–
(
)
×
1
2
--
Io
V
IN
×
t
SW
f
s
×
×
+
=
P
UPPER
(
)
×
D
×
1
2
--
Io
V
IN
×
t
SW
f
s
×
×
+
=
ISL6530
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6530EVAL2 | Dual Low-Noise High-Drive Operational Amplifier 8-SO 0 to 70 |
| ISL6530CR-T | Dual 5V Synchronous Buck Pulse-Width Modulator (PWM) Controller for DDRAM Memory VDDQ and VTT Termination |
| ISL6530CBZ-T | Dual 5V Synchronous Buck Pulse-Width Modulator (PWM) Controller for DDRAM Memory VDDQ and VTT Termination |
| ISL6531 | Dual Low-Noise High-Drive Operational Amplifier 8-SO 0 to 70 |
| ISL6531CR-T | Dual 5V Synchronous Buck Pulse-Width Modulator (PWM) Controller for DDRAM Memory VDDQ and VTT Termination |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6530EVAL2 | 功能描述:EVALUATION BOARD 2 ISL6530 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6531CB | 功能描述:電壓模式 PWM 控制器 Synch Buck - DDRAM RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6531CB-T | 功能描述:IC CONTROLLER INTEL 24SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6531CBZ | 功能描述:IC CONTROLLER INTEL 24SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6531CBZ-T | 功能描述:IC CONTROLLER INTEL 24SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。